Urmet 2Voice 1083/40 Mode D'emploi page 8

where:
ee: number of the main call station (00÷03)
f: is a symbol showing the status of communication; it can be:
...
When the switchboard has not yet answered the call
When the switchboard is in communication with the call station
When the switchboard is in communication with an apartment station
When the switchboard has established a communication between the main call station
and an apartment station.
iiiii:
physical code of the called user (Liiii – in case of logical code)
yyyyyy: name of the called user
c: when the symbol BELL appears in this position, it means that the switchboard has not yet called
the apartment station iiiii; if the attendant presses the button
and this symbol disappears.
After receiving a call, the switchboard can call users by entering the code iiiii followed by the button
When in this condition, the switchboard attendant will be able to:
– establish again a communication with the call station
– call again the user (4)
– establish a communication between the call station and the user
§
When in this last condition, the switchboard can not establish again a communication with the call
station or with the user.
If the switchboard attendant has not yet answered the call coming from the call station, by pressing the
auto-on button (10) the attendant can see images coming from the additional cameras connected
to the main station.
DOOR LOCK RELEASE FUNCTIONS
At any time, the switchboard allows to open any door associated to the main or secondary call station.
Main entrance door opening
The following 2 conditions are possible:
1) After a call coming from a main call station:
when the switchboard is performing the concierge service in DAY mode and is in communication with a
main call station, the attendant can:
• press the button (15) or the door lock release button on the handset to open the pedestrian door
of the caller main station;
• press the button SHIFT (16) + (15) to open the driveway gate of the caller main station.
2) In any other situation:
when the switchboard is NOT in conversation, to open the pedestrian door of a main call station press the
button (15), enter the ID code of the main call station (0÷3) and press the button
door.
MAIN DOOR:
PRESS
13/03/2010
• when the switchboard is NOT in conversation, to open the driveway gate of a main call station press the
button SHIFT (16) + (15), enter the ID code of the main call station (0÷3) and press the button
14
(7), the user iiiii is directly called
(9)
(6)
2
TO OPEN
15:30:30
(7) to open the gate. The display is similar to the previous one.
• When the switchboard is NOT in conversation, to open the pedestrian door of a secondary call station
press the button
(0÷3), enter the address of the secondary (0÷1) and press the button
(7).
In this example, the attendant has opened the door connected to the secondary call station with ID = 15
and secondary address 0.
• When the switchboard is not in conversation, to open the driveway gate of a secondary call station press
the button SHIFT (16) +
station (0÷31), enter the address of the secondary and press the button
display is similar to the previous one.
MANAGEMENT OF CODES FOR SPECIAL SERVICES
The switchboard is enabled to manage electric actuators by using decoders for special services Ref.
1083/80.
Press and keep the button "0" pressed for 3s and enter the actuator special code (1 ÷ 255); the display
shows the following screen:
Confi rm the command with the button
After the button
It also possible to use the function buttons (11), which can be programmed to directly activate special
decoders (see in the chapter "Confi guration" the paragraph "Function Buttons").
(7) to open the
OPEN DOOR INDICATIONS
The switchboard is provided with a led (3), used to indicate the status of doors of main and secondary call
stations.
The feature depends on the status of the terminal pin SP in the call stations and needs an open door
sensor.
The following operating states are possible:
led off:
all main and secondary entrance doors are closed;
led on: on one or more main or secondary entrance doors, the door is open. The condition of open
door is signalled by call stations only if this event lasts for at least 30 seconds.
When the led (3) is on, by pressing the button
DS1083-017 DS1083-017
(14) followed by the button (7), enter the ID code of the secondary call station
SEC. DOOR: 15 - 0
PRESS TO OPEN
13/03/2010 15:30:30
(14) followed by the button
SPEC. CODE:
PRESS TO SEND
13/03/2010 15:30:30
(7).
(7) has been pressed, the display returns to standby mode.
(3) the attendant can access the list of doors left open:
(7) to open the door.
(7), enter the ID code of the secondary call
(7) to open the gate. The
1
15