Publicité
Les langues disponibles
Les langues disponibles
10.4
Checking the chain lubrication (Fig. 13)
Start the device (see section "Switching on the
1.
device").
Hold the chainsaw during operation, at medium
2.
speed, over a sawed-off tree stump or a suitable
surface. If the lubrication is sufficient, a light film
of oil will form on the tree stump or surface.
There is an oil adjustment screw on the bottom
3.
of the chainsaw which can be used to control the
chain lubrication by turning.
- First press and then turn the oil adjustment
screw clockwise to reduce chain lubrication.
- First press and then turn the oil adjustment
screw anti-clockwise to increase chain lubri-
cation.
11. Commissioning
m CAUTION!
Please observe the legal provisions from the noise pro-
tection ordinance.
Before each start-up, check the device for the follow-
ing:
• Leak-tightness of the fuel system
• Faultless condition and completeness of the guards
and the cutting device
• Tight fit of all screw connections
• Working notes on smooth running of all moving parts
• Familiarise yourself with handling the chainsaw be-
fore use.
11.1
Switching on the device (Fig. 14 - 16)
m WARNING!
Ensure that the saw chain is not yet applied to the
cut and that no other objects are touched: Danger
of injury!
• Hold the chainsaw firmly with both hands and make
sure that no persons (in particular children) or ani-
mals are in the immediate vicinity.
• Make sure that the chain brake is released before
starting the chainsaw. To do so, draw the hand
guard back in the direction of the bow-type han-
dle. (Fig. 14)
Press the main switch (17) until the LED lamp
1.
lights up. (Fig. 15)
Press and hold down the switch lock (3).
2.
Press the on/off switch (2). The saw chain (6)
3.
starts running.
Release the switch lock again. (Fig. 16)
4.
42 | GB
11.2
Switching off the device (Fig. 17)
Release the on/off switch (2).
1.
Press the main switch (17) until the LED lamp
2.
goes out.
11.3
Displaying the charge level (Fig. 18)
By pressing the button on the battery (18) it is
1.
possible to check the charge level with the battery
charge indicator LED (20).
The light goes out after 5 seconds. If the LED
2.
flashes, the battery (18) must be charged. If no
LED lights up when the button is pressed, the bat-
tery (18) is defective and must be replaced.
12. Basic working notes
m Attention!
Always make sure the device is fully assembled
before commissioning!
Danger of injury!
Sawing and felling work as well as all related work may
only be carried out by specially trained and briefed
persons.
Note
Observe the country-specific regulations for felling
work and obtain information from the relevant author-
ity.
• Make sure that no one can be harmed by the falling
branches and trees.
• Only the persons required for the felling work may
be in the work area.
• Keep the work area at the trunk clear and tidy so
that operators have a safe standing area.
• Keep escape routes clear and tidy in order to be
able to leave the work area quickly.
• Do not carry out felling work in stronger wind con-
ditions, bad weather or poor visibility.
• Keep distances to the nearest workplace of at least
2 1/2 tree lengths.
12.1
Use and handling
• Never start the device before the guide rail (7), saw
chain (6) and chain cover (12) are correctly fitted.
• Do not cut wood that is lying on the ground or try to
cut roots that are sticking out of the ground.
• In any case, make sure the saw chain (6) does not
come into contact with the soil, otherwise the saw
chain (6) will dull immediately.
www.scheppach.com
Publicité
