Berner BMS-777-1 Traduction De La Notice D'instructions D'origine page 44

EngLIsh

WARNING: When sawing aluminium, remove the dust
bag, or disconnect the dust extractor to avoid the risk of
fire.
Your mitre saw has a built-in dust port
connection to either a dust bag (33 mm nozzles) or direct
attachment to the BERNER AirLock (DWV9000-XJ)
Observe the relevant regulations in your country for the
materials to be worked.
To Attach the Dust Bag
1. Fit a dust bag to the dust port
To Empty the Dust Bag
1. Remove dust bag from the saw and gently shake or tap the
dust bag to empty.
2. Reattach the dust bag back onto the dust port.
You may notice that all the dust will not come free from the
bag. This will not affect cutting performance but will reduce the
saw's dust collection efficiency.
To restore your saw's dust collection efficiency, depress the
spring inside the dust bag when you are emptying it and tap it
on the side of the trash can or dust receptacle.
External Dust Extraction
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special dust Class M vacuum
cleaner.
connecting to an airLock compatable Dust Extractor
(Fig. T)
The dust port 31 on your mitre saw is compatable with the
BERNER AirLock connection system. The AirLock allows for a fast,
secure connection between the dust extractor hose and the
mitre saw.
1. Ensure the collar on the AirLock connector
unlock position. Align notches on collar and AirLock
connector as shown for unlock and lock positions.
2. Push the AirLock connector onto the dust port
3. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and
secure the connection. The mitre saw is now securely
connected to the dust extractor.
MAINTENANCE
Your BERNER power tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.

WARNING: If the saw blade is worn, replace it with a new
sharp blade.
44
31 that allows
.
45
31 .
45 is in the
31 .
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable
lower blade guard as well as the dust extraction tube to
determine that it will operate properly. Ensure that chips, dust
or workpiece particle cannot lead to blockage of one of the
functions.
In case of workpiece fragments jammed between saw blade
and guards disconnect the machine from the power supply and
follow the instructions given in section Changing or Installing
a New Saw Blade. Remove the jammed parts and reassembling
the saw blade.

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean
the table top.

WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
Optional Accessories

WARNING: Since accessories, other than those offered
by BERNER , have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only BERNER recommended
accessories should be used with this product.
Range of saw blades available
(recommended blades)
Type of blade Blade dimensions
(diameter × bore × no.
of teeth)
DT4310 series 40 216×30×24
DT4286 series 40 216×30×80
DT4320 series 60 216×30×48
DT4350 series 60 216×30×60
Usage
For general purpose,
ripping and crosscutting of
wood and plastics
TCG for use with aluminum
ATB for fine cutting of
manmade and natural
wood
TCG for extra fine cutting
of manmade and natural
wood