Publicité
Les langues disponibles
Les langues disponibles
2. Place your thumb on the mitre arm
mitre latch 12 to release the rotating table
11
.
3. Swing the mitre arm until the latch locates it at the 0° mitre
position.
4. Pull down the head and lock it in this position using the lock
down button
.
21
5. Check that the two 0° markings
are just visible.
6. Place a square
40
(Fig. J) against the left side of the fence
and blade
.
15
7
WARNING: Do not touch the tips of the blade teeth with
the square.
7. If adjustment is required, proceed as follows:
a. Loosen the screws
39
assembly left or right until the blade is at 90° to the fence
as measured with the square.
b. Retighten the screws
Checking and Adjusting the Blade to the
Table (Fig. B, J–L)
1. Loosen the bevel clamp handle
2. Press the saw head to the right to ensure it is fully vertical
and tighten the bevel clamp handle.
3. Place a set square
40
on the table and up against the blade
(Fig. I).
7
WARNING: Do not touch the tips of the blade teeth with
the square.
4. If adjustment is required, proceed as follows:
a. Loosen the bevel clamp handle
position adjustment stop screw
hex wrench (as shown in Fig. K) until the blade is at 90° to
the table as measured with the square.
b. If the bevel pointer
the bevel scale
, loosen the screws
19
scale and move the scale as necessary.
Checking and Adjusting the Bevel Angle
(Fig. K, L)
The bevel override allows the maximum bevel angle to be set at
45° or 48° as required.
•
Left = 45°
•
Right = 48°
1. Make sure the override lever
position.
2. Loosen the bevel clamp handle
then down and move the saw head to the left.
3. This is the 45° bevel position.
If adjustment is required, turn the stop screw
necessary until the pointer
Prior to Operation
•
Install the base extensions to both sides of the saw's base.
Refer to Assembling the Base Extensions section.
11
and squeeze the
/ mitre arm
13
on the mitre scale
38
and move the scale/mitre arm
.
39
18
(Fig. K).
18
and turn the vertical
in or out with the
41
42
(Fig. L) does not indicate zero on
that secure the
43
is located in the left
29
18
by pulling it outward
44
in or out as
42
indicates 45°.
•
Check the protective belt cover for damage and the proper
functioning of the lower guard.
•
Make sure to use the kerf plate. Do not operate the machine
if the kerf slot is wider than 12 mm.
•
Install the appropriate saw blade. Do not use excessively
worn blades. The maximum rotation speed of the tool must
not exceed that of the saw blade.
•
Make sure all locking knobs and clamp handles are tight.
14
•
Use personal protective equipment and connect the saw to
an external dust extractor.
•
Although this saw will cut wood and many nonferrous
materials, these operating instructions refer to the cutting
of wood only. The same guide-lines apply to the other
materials. Do not cut ferrous (iron and steel) materials, fibre
cement or masonry with this saw!
•
Do not attempt to cut excessively small pieces.
•
Secure the workpiece.
•
Allow the blade to cut freely. Do not force.
•
Allow the motor to reach full speed before cutting.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Ensure the machine is placed to satisfy your ergonomic
conditions in terms of table height and stability. The machine
site shall be chosen so that the operator has a good overview
and enough free surrounding space around the machine that
allows handling of the workpiece without any restrictions.
To reduce effects of increased vibration, make sure the
environment is not too cold, the machine and accessory are well
maintained and the workpiece size is suitable for this machine.
Switching On and Off (Fig. A)
A hole
28
is provided in the on/off switch
a padlock to lock the tool.
1. To run the tool, press the on/off switch
2. To stop the tool, release the switch.
Use of LED Worklight System (Fig. A, M)
nOTE: The mitre saw must be connected to a power source.
The LED Worklight System is activated with a push button
switch, fitted on the handle under the guard lock release lever
2
. The LED Worklight System is independent of the mitre
saw's trigger switch. A failure of LED has no effect on the
intended operation.
To cut through an existing pencil line on a piece of wood:
EngLIsh
1
for insertion of
1
.
41
Publicité
