Regency City Serie Manuel D'utilisation Et D'installation page 49

8. Attach 2x Part G to the previously installed Part J parts with 2 screws
at each end.
G
9. Attach end cross braces (Parts E + F) with 2 screws at each end as
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
shown below.
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR =
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
E
10. Install Part A (x2) to Part G on each side with 2 screws on each end.
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR =
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
A
A
920-718a 3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR =
G
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
PROCESS :
1:24
SCALE: PART :
vkrishnamurthy 8/1/2023
DWN: DATE:
1
E.C.N.: SIGN: DATE:
F
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
PROCESS :
1:24
SCALE: PART :
8/1/2023
vkrishnamurthy
DWN: DATE:
1
E.C.N.: SIGN: DATE:
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
PROCESS :
1:24
SCALE: PART :
8/1/2023
vkrishnamurthy
DWN: DATE:
1
E.C.N.: SIGN: DATE:
11. Install 4 horizontal mid braces (Part K) at the top and bottom to
the Part A. Add the Part K to the Part I and screw them together
with the Part A.
12. Install 2 front supports (Part C) to upper- and lower-Part A with 2
screws on each end.
-
SHEAR/ PUNCH/ FORM
CITY 48 BAY ASSEMBLY
PART NO: REV:
482-502
-
-
SHEAR/ PUNCH/ FORM
CITY 48 BAY ASSEMBLY
PART NO: REV:
482-502
-
3RD ANGLE
PROJECTION
DO NOT SCALE
DRAWING
UNITS IN INCHES
3
-
SHEAR/ PUNCH/ FORM
CITY 48 BAY ASSEMBLY
PART NO: REV:
482-502
-
CITY SERIES
consignes d'installation
K
K
K
K
3RD ANGLE TOLERANCES UNLESS
FIREPLACE PRODUCTS
PROJECTION OTHERWISE STATED
INTERNATIONAL
DIMENSIONS
0.000 = 0.01 CRITICAL
1:24
SCALE:
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING vkrishnamurthy
DWN:
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR = 1
E.C.N.:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
C
C
TOLERANCES UNLESS
FIREPLACE PRODUCTS
OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
SCALE:
0.000 = SPECIFIED TOLERANCE
0.000 = 0.031
vkrishnamurthy
DWN:
0.000 REF = REFERENCE ONLY
ANGULAR = 1
E.C.N.:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
Foyer City Series CB50E |
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CITY 48 BAY ASSEMBLY
PART :
8/1/2023 PART NO: REV:
DATE:
482-502
-
SIGN: DATE:
-
MAT'L :
INTERNATIONAL
SHEAR/ PUNCH/ FORM
PROCESS :
1:24 CITY 48 BAY ASSEMBLY
PART :
8/1/2023
PART NO:
DATE:
482-502
SIGN: DATE:
49
09.07.23
REV:
-