Regency City Serie Manuel D'utilisation Et D'installation page 48

CITY SERIES
consignes d'installation
2. Install the frame assembled in Step 1, onto the back of the unit as
shown with 2 screws on each side.
3. Place unit against wall in desired location. Level the unit by adjusting
3RD ANGLE TOLERANCES UNLESS
4 leveling bolts on unit.
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
4. Install venting before proceeding further with framing kit construction.
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
Refer to manual for venting instructions.
UNITS IN INCHES ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
5. Secure the unit with framing to the wall studs with 2-1/2"-3" wood
screws (not supplied). Use 8 screws and secure to 4 studs minimum.
Ensure the frame is also secured to the 2 additional studs spaced 57-1/4"
apart center to center, using the last hole on the upper- and lower-part
B framing part as shown below.
48 | Foyer City Series CB50E
3RD ANGLE
PROJECTION
920-718a
DO NOT SCALE
DRAWING
UNITS IN INCHES
FIREPLACE PRODUCTS
INTERNATIONAL
1:24
SCALE:
vkrishnamurthy
DWN:
E.C.N.: SIGN:
57 1/4"
TOLERANCES UNLESS
FIREPLACE PRODUCTS
OTHERWISE STATED
INTERNATIONAL
DIMENSIONS
0.000 = 0.01 CRITICAL
1:24
SCALE:
0.000 = SPECIFIED TOLERANCE
0.000 = 0.031
vkrishnamurthy
DWN:
0.000 REF = REFERENCE ONLY
ANGULAR = 1
E.C.N.:
6. Attach the 2 center supports (Part I) to upper- and lower-part B of
the back frame with 2 screws each as shown.
7. Attach the 4 x end pieces (Part J) to the upper- and lower-Part B of
the back frame with two screws each.
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CITY 48 BAY ASSEMBLY
PART :
8/1/2023
PART NO: REV:
DATE:
482-502
-
DATE:
3RD ANGLE
PROJECTION
DO NOT SCALE
DRAWING
UNITS IN INCHES
-
MAT'L :
2
SHEAR/ PUNCH/ FORM
PROCESS :
CITY 48 BAY ASSEMBLY
PART :
8/1/2023
PART NO:
DATE:
482-502
DATE:
SIGN:
I
3RD ANGLE TOLERANCES UNLESS
PROJECTION OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
J
J
TOLERANCES UNLESS
OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
SCALE:
0.000 = SPECIFIED TOLERANCE
0.000 = 0.031
DWN:
0.000 REF = REFERENCE ONLY
ANGULAR = 1
E.C.N.:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
REV:
-
I
FIREPLACE PRODUCTS -
MAT'L :
INTERNATIONAL
SHEAR/ PUNCH/ FORM
PROCESS :
1:24 CITY 48 BAY ASSEMBLY
SCALE: PART :
9/1/2023
PART NO:
DWN: DATE:
482-502
DATE:
E.C.N.: SIGN:
J
J
FIREPLACE PRODUCTS -
MAT'L :
INTERNATIONAL
SHEAR/ PUNCH/ F
PROCESS :
1:24 CITY 48 BAY ASSEMBL
PART :
vkrishnamurthy 8/1/2023
PART NO:
DATE:
482-502
SIGN: DATE:
09.07.23