Publicité
Les langues disponibles
Les langues disponibles
Handling
Folding up
(6.1)
First remove the seat cushion from
the wheelchair and flip up the
(platform) footplate or the individu-
al footplates. Take hold of the sling
from underneath in the middle and
pull upwards. The wheelchair will
then fold up. To fold your
wheelchair until it is as small as
possible, e.g., to put into a car, you
can remove the footrests (depend-
ing on the model). For this pur-
pose, open the latch from the out-
side and swing the footrest to the
side. Then the footrest only has to
be drawn out of the frame tubing.
Unfolding
Open the strap on folded frame
prior to unfolding.
Press down on the seat tubing
(see picture). Your wheelchair is
then unfolded. Now snap the seat
tubing into position in the seat
saddle. This can be facilitated by
slightly tipping your wheelchair. In this way, the
weight can be taken off of one rear wheel so that
the wheelchair can be more easily unfolded. Be
careful not to get your fingers caught in the cross-
tube assembly.
Quick-Release Axles for Rear
Wheels
(6.2)
The rear wheels are equipped with
quick-release axles. The wheels
can thus be installed or removed
without using tools. To remove a
wheel, simply depress the quick-
release button on the axle (1) and
pull it out.
CAUTION:
Hold the quick-release button on
the axle depressed when inserting
the axle into the frame to mount the rear wheels.
Release the button to lock the wheel in place.
The quick-release button should snap back to its
original position.
Quick-Release Axles for Casters
(6.3)
Casters can also be equipped with
quick-release axles (1), which can
then either be installed or removed
without using tools.
8
YOUNGSTER 3
All manuals and user guides at all-guides.com
Tipping Tubes
Tipping tubes are used by atten-
dants to tip a wheelchair over an
obstacle. Simply step on the tube
to push a wheelchair, for example,
over a curb or step.
02.1
Wheel Locks
Your wheelchair is equipped with
two wheel locks. They are applied
directly against the tires. To enga-
ge, press both wheel-lock levers
forward against the stops (Fig. 1).
To release the wheel, pull the
02.2
levers back to their original posi-
tions.
Braking power will decrease with:
• Worn tire tread
• Tire pressure that is too low
• Wet tires
• Improperly adjusted wheel locks.
The wheel locks have not been
designed to be used as brakes for
a moving wheelchair. The wheel
locks should therefore never be
used to brake a moving
wheelchair. Always use the hand-
rims for braking. Make sure that
the interval between the tires and
wheel locks complies with given
specifications (Fig. 2). To readjust,
loosen screw (1) and set the
appropriate interval. Tighten screw (see the page on
torque).
1
CAUTION:
After each adjustment of the rear wheels, check
the interval to the wheel locks and readjust if
04
necessary.
Extension for the Brake Lever
(7.11)
The extension for the brake lever
can be removed or folded down.
The longer lever helps to minimize
the effort needed to set the wheel
locks.
Caution:
Mounting the wheel lock too
close toward the wheel will
result in a higher effort to
operate. This might cause the
brake lever extension to break!
1
Leaning onto the brake lever extension while trans-
ferring will cause the lever to break! Splashing water
06
from tires might cause the wheel lock to malfunc-
tion.
Options – Tipping Tubes
(7.1)
Options – Brakes
(7.10)
07
351
352
354
Rev.A 1104/500/ST/000690636.EMS.1
Publicité
