Publicité
Les langues disponibles
Les langues disponibles
®
FX
Marking
cartridges 9mm, .38
cal. and 5.56mm
This FX
•
®
The FX
9004 Helmet, Head Protector, by itself, will not provide complete head protection from FX
Helmet, Head Protector must be worn with the user's ballistic helmet or with the FX
•
®
The FX
9004 Hard Top Cover (8971905SP) is an integral part of the FX
the required protection to the head area. To provide complete neck and head protection, this FX
required to be worn in conjunction with the FX
8971771).
•
®
The FX
9004 Helmet, Head Protector lens and lens frame should never be separated from the Goggle Assembly for cleaning. If lens
and frame should become separated, users must not attempt to re-install.
(8971021SP) must be used and reinstalled. Failure to follow these instructions may result in severe eye injury. Always inspect the FX
9004 Helmet, Head Protector and the Goggle Assembly for signs of damage; replace components and/or complete the FX
Helmet, Head Protector as required for proper safety.
•
The use of approved Simunition
training with 9mm, .38 cal. and 5.56mm FX
•
FOR SAFE AND EFFECTIVE USE OF THIS EQUIPEMENT, FOLLOW ALL INSTRUCTIONS.
•
General Dynamics-Ordnance and Tactical Systems Canada is not responsible for injuries, loss, or damage resulting from misuse
of this equipment. THIS PRODUCT WILL NOT PROVIDE UNLIMITED FACE AND EAR PROTECTION.
•
Intended only for supervised law enforcement and military training conducted in accordance with Simunition
•
Should protective lens become fogged or dirty during training, DO NOT REMOVE IT! ASK FOR ASSISTANCE FROM THE
INSTRUCTOR TO REMOVE YOURSELF FROM THE TRAINING AREA WITH FX
•
Check the lens before each use and replace immediately if cracks or dents are observed. No lens can protect the wearer from all
potential impacts and will not protect against all impacts nor will it protect against all chemical splashes. DO NOT USE TO PLAY
PAINTBALL.
•
Do Not Use Abrasive Cleaning Products or Liquids Containing Ammonia or Alcohol, or Chlorine, or other chemical products on any
surface of the Lens (Interior Fog-Resistant and Exterior -Scratch resistance).
•
N.B.: DO NOT PUT ANY FX
DRYER.
•
®
REPLACE THE FX
9003/9004 GOGGLE ASSEMBLY (8971021SP) IF DAMAGED.
© 2022 General Dynamics-OTS Canada
CAUTION
®
•
The FX
9004 Helmet, Head Protector has been designed and developed to be used
only with the following calibers of Simunition
Training Ammunition (where applicable); 9mm, .38 cal. and 5.56mm as well as Force on
®
Force
(FoF) Marking Ammunition.
•
DO NOT USE WITH ANY OTHER TYPE OR CALIBER OF AMMUNITION.
•
The use of this equipment is MANDATORY to prevent serious personal injury to head
and face during training with FX
will not provide unlimited face and head protection.
®
9004 Helmet, Head Protector comes assembled and ready to wear.
®
9000 Throat Protection (8971764) and FX
®
Protective equipment is MANDATORY to prevent serious personal injury to ears and face during
®
Marking and non-Marking cartridges as well as FoF Marking cartridges only.
®
9004 HELMET, HEAD PROTECTOR COMPONENTS IN THE WASHING MACHINE OR SPIN
Registered trademarks of General Dynamics Ordnance and Tactical Systems-Canada Inc. are denoted by
®
FX
®
marking/non-marking cartridges, however, this product
®
®
9004 Helmet, Head Protector and must be worn to provide
A brand-new FX
®
9004 HELMET, HEAD PROTECTOR IN PLACE.
www.simunition.com
®
Interactive Marking & Non-Marking
®
marking rounds. The FX
9004 Hard Top Cover (8971905SP) (included).
®
9004 Helmet, Head Protector is
®
9000 Groin (male 8971770 and female
®
9003/9004 Goggle Assembly
®
safety guidelines.
®
.
®
9004
®
®
9004
Page 4 of 52
8972330.FTSIM_rev00
Publicité
