Securing The Support Bar; Mounting The Support Panels; Mounting The Bottom Chamber Assembly; Mounting The Power Cord Bracket - Pit Boss 2 Serie Mode D'emploi

3. SECURE CONTROL BOARD TO FRONT SUPPORT LEGS
Parts Required:
2 x #10–24x½" Screw ( #C)
Installation:
• Near the Control Board, loosen the two screws connecting the front
panel to the main cabinet.
• Using another two screws, secure the front panel sides to the front-
facing support legs. Once these screws are tight, re-tighten the two
screws that were previously loosened.

4. SECURING THE SUPPORT BAR

Parts Required:
1 x Support Bar (#16)
4 x #10–24x½" Screw ( #C)
Installation:
• Install the support bracket to the rear of the unit between the two
rear support legs. Secure using two screws on each side. Ensure the
support bracket is place on the underside of the main cabinet, facing
inwards. Note illustration for support bracket arrangement.
NOTE: The support bracket with two holes along the bottom should
be on the same side of the unit as the power cord exits the control
board (left side). This is important for later steps.

5. MOUNTING THE SUPPORT PANELS

Parts Required:
2 x Support Panel (#17)
8 x #10–24x½" Screw ( #C)
Installation:
• Install one support panel to the side of the unit between a front and
back support leg. Secure using two screws on each side. Ensure the
flat side of the support plate is facing outwards. Repeat the same
installation to mount the other support panel. Note illustration for
support panel arrangement.

6. MOUNTING THE BOTTOM CHAMBER ASSEMBLY

Parts Required:
1 x Bottom Chamber Assembly (#20)
4 x #10–24x½" Screw (#C)
Installation:
• Mount the bottom chamber assembly to the bottom of the cabinet
base using four screws. Ensure the rails for the grease tray are facing
the front of the unit.
8
3
4
16
5
17
6
20
FRONT

7. MOUNTING THE POWER CORD BRACKET

Parts Required:
1 x Power Cord Bracket (#19)
2 x #10–24x½" Screw (#C)
Installation:
• Loosen the screw of the power cord clip on the support leg, and guide
the power cord through the power cord clip to secure.
• Locate the two holes on the bottom of the (left side) support bracket.
Mount the power cord bracket to the support panel using two screws
as shown in illustration 7A. Once secure, wrap the power cord on the
bracket until unit is in use.
• Proceed to fully-tighten all screws on the cabinet base, then carefully
turn the cart upright with the wheels on the bottom. Note 7B.
IMPORTANT: Ensure that all screws on the cabinet base are fully-
tighten to avoid screws falling out when the unit is moved.

8. INSTALLING THE DAMPERS INTO THE MAIN CABINET

Parts Required:
Main Cabinet (#9)
1 x
2 x Damper Vent (#3)
2 x #10–24x½" Screw (#C)
2 x #10-24 Lock Nut (#D)
M5 Locking Washer (#E)
2 x
Installation:
• First, lift the main cabinet door off the hinges, and place aside. Note 8A.
• Place one screw from the outside of the main cabinet into the center
of each damper. Next, insert a damper inside the main cabinet with
the raised tab facing the rear, and secure the screw from the exterior
using a locking washer and lock nut. Repeat same installation for
second damper, as shown in illustration 8B.

9. MOUNTING THE BACK HANDLE

Parts Required:
1 x Back Handle (#4)
¼–20x⅝" Screw (#A)
4 x
Installation:
• Mount the handle onto the back side of the main cabinet using four
screws. Note correct position as shown, with handle on top.
7A
19
7B
8A
9
8B
3
3
9
4
9