Parts & Specs; Assembly Preparation; Mounting The Wheels To The Support Legs - Pit Boss 2 Serie Mode D'emploi

PARTS & SPECS
Part# Description
1 Cooking Grids (x3)
2 Cooking Grid Support Brackets (x6)
3 Damper Vent (x2)
4 Back Handle (x1)
5 Logo Plate (x1)
6 Cabinet Door Handle (x1)
7 Cabinet Door Latch (x1)
8 Cabinet Door (x1)
9 Main Cabinet (x1)
10 Wood Chip Tray Lid (x1)
11 Wood Chip Tray Assembly (x1)
12 Door Grease Shield (x1)
13 Water Pan (x1)
14 Water Pan Support (x1)
15 Cabinet Base (x1)
16 Support Bar (x1)
17 Support Panel (x2)
18 Grill Probe Bracket (x1)
19 Power Cord Bracket (x1)
20 Bottom Chamber Assembly (x1)
21 Support Legs (x4)
22 Locking Caster Wheel (x2)
23 Caster Wheel (x2)
24 Grease Tray (x1)
25 Meat Probe (x1)
A ¼–20x⅝" Screw (x4)
B ¼–20x½" Screw (x28)
C #10–24x½" Screw (x34)
D #10–24 Lock Nut (x2)
E M5 Locking Washer (x2)
F #8–32" Screw (x5)
G #5–32x½" Screw (x2)
H Spare Hardware
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Care if parts are missing when assembling the unit.
MODEL ASSEMBLED (WXDXH) WEIGHT
553 MM X 513 MM X 1,048 MM 26.5 KG
PB
PBV2D1
/ 21.7 IN. X 20.2 IN. X 41.2 IN. / 58.4 LB
6
1
2
3
4
8
5
9
6
7
12
10
15
13
11
14
16
17
20
17-1
17-2
21
19
18
24
21-3
23 22
25
21-1 21-2
A D G
B E H
C F
PB – ELECTRIC REQUIREMENTS
110-120V, 60Hz, 1650W, 3-PRONG GROUNDED PLUG
COOKING AREA TEMPERATURE RANGE
CUBIC COOKING: 0.05 M / 2.0 FT 38-204°C
3 3
TOTAL - 3,608 CM² / 559.3 IN² / 100-400°F
Parts are located throughout the shipping carton, including underneath the smoker. Inspect the unit, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the griddle
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care for parts.
www.pitboss-grills.com | USA: (480) 923-9630 | CANADA (TOLL FREE): 1-877-942-2246
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
Tools required for assembly: screwdriver and level. Tools not included.
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws
completely until all screws for that step have been installed, or unless otherwise mentioned.

1. MOUNTING THE WHEELS TO THE SUPPORT LEGS

Parts Required:
2 x Locking Caster Wheel (#22)
2 x Caster Wheel (#23)
4 x Support Legs (#21)
¼–20x½" Screw (#B)
16 x
Installation:
• Place a piece of cardboard on the floor to prevent scratching the unit
and parts during assembly. Next, attach the wheel to the bottom of
the leg using four screws. Repeat installation for the other support
21--4
legs and wheels.
2. MOUNTING THE SUPPORT LEGS TO CABINET BASE
Parts Required:
1 x Cabinet Base (#15)
12 x ¼–20x½" Screw (#B)
Installation:
• Next, lay the cabinet base on the floor, upside down. Prepare the four
support legs for installation to the cabinet base, arranging the labelled
legs as shown in the illustration.
IMPORTANT: The four support legs must be arranged correctly to
properly install the support panels and support bar in later steps.
The locking caster support legs must be installed at the back of the
Cabinet Base.
• Mount one support leg to the cabinet base using three screws. Repeat
installation for the other three support legs. Tighten inside screws
completely, but leave outside screws partly loosened.

ASSEMBLY PREPARATION

ASSEMBLY INSTRUCTIONS
1
2
21-1
21-2
22
23
21
21-4
21-3
15
7