Lock
18
Cover
19
Dosing head
20
Detergent CA 50 C (0.5 l round bottle)
21
Cleaning rollers (replacement)
22
*Battery pack Battery Power 18/25 DW
23
or
Battery pack Battery Power+ 18/30 DW
*Mains cable for quick charger
24
*Quick charger Battery Power 18/25
25
or
Quick charger Battery Power+ 18/60
Cleaning rollers
26
*BR 30/1 C Bp Pack
Initial startup
Battery pack charging
1. Charge the battery pack (see operating instructions
and safety instructions for the battery pack and the
charger).
Inserting the battery pack
1. Push the battery pack into the battery mount on the
device until the battery pack audibly latches into
place.
Illustration B
Cleaning and care agents
ATTENTION
Use of unsuitable detergents and care agents
The use of unsuitable detergents and care agents can
damage the device and loss of eligibility for warranty
claims.
Use only KÄRCHER detergents.
Take care to ensure the correct dosage.
Note
Use KÄRCHER detergent or care agents for floor clean-
ing as necessary.
Observe the manufacturer's dosing quantity recom-
mendations when dosing with detergent or care
agents.
To prevent foaming, fill the fresh water tank with wa-
ter first and the add the detergent or care agent.
To prevent the tank from overflowing, be sure to
leave enough space for the detergent or care agent
when filling with water.
Filling the fresh water tank
1. Grasp the fresh water tank by the recessed grips at
the side and take it out of the device.
Illustration C
2. Open the tank cap.
Illustration D
3. Fill the fresh water tank with clean tap water
(max. 40 °C) up to the MAX marking at most. If de-
tergent is to be used, fill in less fresh water accord-
ingly.
4. Add KÄRCHER detergent or care agent to the fresh
water tank as required.
ATTENTION
Over- or underdosing of the detergent or care agent
Can result in poor cleaning results.
Observe the recommended dosage for the detergent
and care agents.
Note
For optimal cleaning and care results, we recommend
using only KÄRCHER products and the dosing head.
5. Unscrew the round bottle lock.
Illustration E
6. Screw the dosing head onto the round bottle.
7. Squeeze the round bottle in the middle until the re-
quired amount of detergent has flowed into the dos-
ing head.
Illustration F
Take the following into account:
a The specifications of the detergent manufacturer
for the mixing ratio of detergent and fresh water
b the corresponding scale on the dosing head
c the capacity of the tank
8. Open the cover on the dosing head.
9. Fill the detergent into the tank.
Illustration G
10. Close the cover on the dosing head.
11. Close the tank cap.
12. Insert the fresh water tank into the device until it
latches into place.
General notes on operation
ATTENTION
Moisture
Material damage to sensitive floors
Check the surface to be cleaned for water sensitivity at
an inconspicuous location before using the device.
Do not clean water-sensitive floor coverings such as
e.g. untreated cork floors, since the moisture can pene-
trate and damage the floor.
ATTENTION
Risk of damage due to moisture and detergents as
well as the device tipping over
Risk of material damage on sensitive floors and on the
cleaning rollers due to prolonged exposure to moisture
and detergents.
Risk of material damage if the device falls over.
Always move the device to the parking position when
you take a break from work and after work.
Do not lean the device against walls, doors or other ob-
jects when setting it down.
ATTENTION
Material damage
Damage to the device from pointed, large and/or bulky
objects.
Do not use or store the device on hard, coarse dirt and
hard objects, as the parts can become jammed under
the waste water tank and can cause scratches on the
floor and waste water tank.
Before starting work and storing the device, remove ob-
jects such as shards, pebbles from the floor.
● For an optimum cleaning result, wash the cleaning
rollers in the washing machine at 60°C before initial
use.
● Work backwards towards the door so that no foot-
prints are generated on the freshly cleaned floor.
Illustration H
English
Operation
15