Kärcher BR 30/1 C Bp Manuel D'utilisation page 18

2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Empty the waste water tank (see chapter Emptying
the waste water tank).
4. Pull the lid handle and remove the lid.
Illustration T
5. Clean the waste water bowl and the lid with tap wa-
ter.
Illustration U
6. Allow the waste water bowl and the lid to dry or dry
them with a lint-free cloth.
7. Assemble the waste water tank in reverse order and
insert it into the device.
Cleaning the sweep bins
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device after each appli-
cation.
Clean the sweep bins regularly.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Remove the waste water tank (see chapter Empty-
ing the waste water tank).
4. Remove the sweep bins.
a Disengage the sweep bins to the side and swing
them forward.
b Remove the sweep bins to the side.
Illustration V
5. Clean both sweep bins under running water.
Illustration W
6. Remove the cleaning brush from the cover of the
waste water tank, and remove any dirt stuck in the
combs (shown with a frame).
7. Install the two sweep bins in the reverse order.
Cleaning the cleaning roller
ATTENTION
Detergent residues in the cleaning rollers
Foaming
Wash the cleaning rollers under running water or wash
the cleaning rollers in the washing machine each time
after use.
ATTENTION
Damage caused by washing the cleaning rollers
with fabric softener or using a tumble dryer
Damage to the microfibres
Do not use fabric softener when washing the cleaning
rollers in the washing machine.
Do not dry the cleaning rollers in a clothes dryer.
Do not bleach or iron the cleaning rollers.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Reach into the recessed grips on the side of the
cleaning rollers and unscrew the cleaning rollers.
Illustration X
4. Clean the cleaning rollers under running water or
wash them in the washing machine at max. 60°C.
Illustration Y
18
5. Clean the roller drives with a moist cloth.
6. Turn the cleaning rollers on the roller drives. Pay at-
tention to the colour assignment of the inside of the
roller and the roller drive (green to green and blue to
blue).
Illustration Z
7. Allow the rollers to dry mounted on the device or
standing vertically.
Cleaning the water distribution strips
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device after each appli-
cation.
Clean the water distribution strips regularly.
1. Press the ON/OFF switch.
Illustration L
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Remove the waste water tank (see chapter Empty-
ing the waste water tank).
4. Remove the cleaning rollers (see chapter Cleaning
the cleaning roller).
5. Remove the covers on the water distribution strips.
Illustration AA
Installation information
Note the side markings on the covers and on the device
(L to L and R to R).
6. Clean the covers under running water.
7. Clean both water distribution strips (shown with a
frame) with a damp cloth.
Illustration AB
8. Check the fresh water inlet openings (arrows) for
contamination; if necessary, remove stubborn dirt
with the cleaning brush.
9. Assemble in the reverse order.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
The cleaning rollers do not turn and the warning
light lights up
The safety switch-off of the drive motor has triggered,
e.g. B. by excessive pressure on the cleaning rollers or
by driving against a wall or corner.
 Press the ON/OFF switch twice.
Only move the device back and forth when cleaning,
do not exert any pressure on the device.
The cleaning rollers are blocked.
 Check whether an object is jammed on the cleaning
rollers. Remove the jammed object.
 Check whether dirt has accumulated in the sweep
bins and remove it (see chapter Cleaning the
sweep bins).
 Check that the sweep bins are fitted correctly. For
this, remove the sweep bins and then fit them back
in place.
English