Stanley SM18 Mode D'emploi page 25

Cleaning
Before use, carefully check the upper blade guard,
movable lower blade guard as well as the dust extraction
tube to determine that it will operate properly. Ensure that
chips, dust or workpiece particle cannot lead to blockage
of one of the functions.
In case of workpiece fragments jammed between saw
blade and guards disconnect the machine from the
power supply and follow the instructions given in section
Mounting the Saw Blade. Remove the jammed parts and
reassembling the saw blade.
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust
mask when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the
materials used in these parts. Use a cloth
dampened only with water and mild soap. Never
let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
WARNING: To reduce the risk of injury,
regularly clean the table top.
WARNING: To reduce the risk of injury,
regularly clean the dust collection system.
To maintain
RELIABILITY, repair, carbon brush inspection
and replacement, any other maintenance or adjustment
should be performed by STANLEY Service Centers,
always using Stanley replacement parts.
OPTIONAL ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of
injury, only STANLEY, recommended accessories should
be used with this product.
Consult your dealer for further information on the appro-
priate accessories.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be dis-
posed of with normal household waste.
Should you find one day that your STANLEY prod-
uct needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Please sort it
out for separate recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent environmen-
tal pollution and reduces the demand for raw materials.
NOTES
STANLEY's policy is one of continuous improvement to
our products and as such, we reserve the right to change
product specifications without prior notice.
products SAFETY
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all coun-
tries. Contact your local STANLEY dealers for range avail-
ability.
SERVICE INFORMATION
STANLEY offers a full network of company-owned and/
or authorized service agents throughout your country. All
STANLEY Service Centers are staffed with trained per-
sonnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice,
repair, or genuine factory replacement parts, contact the
STANLEY location nearest to you.
TECHNICAL DATA
MITRE SAW
Voltage
Frequency
Power input
Blade diameter
Blade kerf thickness
Bore diameter
Max.blade speed
Mitre (max. positions)
and
Bevel (max. positions)
0°mitre,0°bevel
45°mitre,0°bevel
0°mitre,45°bevel
45°mitre,45°bevel left
0°mitre,45°bevel right
45°mitre,45°bevel right
Automatic blade brake time
Weight
Level of sound pressure according to EN 62841:
Sound pressure (L
Sound pressure uncertainty (K
Sound power (L
WA
Sound power uncertainty (K
ENGLISH (
Original Instructions)
V
AC
Hz
W
mm
mm
mm
min
-1
left
right
left
right
92mm x 285mm / 80mm x 310mm
92mm x 190mm / 80mm x 210mm
left
47mm x 285mm / 45mm x 310mm
47mm x 190mm / 45mm x 210mm
35mm x 285mm / 25mm x 310mm
35mm x 190mm / 25mm x 210mm
s
kg
) dB(A)
pA
) dB(A)
pA
) dB(A)
) dB(A)
WA
SM18
220~240
50-60
1800
254
2.8
30
4800
47°
52°
45°
45°
<10.0
18.6
94,5
3
105,0
3
25