Fitting Instructions - R&G LP0133BK Mode D'emploi

FITTING INSTRUCTIONS


To fit the R&G tail tidy, first remove the pillion seat using the key.

Unclip the electrical connection that powers the licence plate illuminator and the indicators and
remove the 4 bolts that secure the OEM licence plate hanger in place, as shown in picture 1.

Gently pull the wire through the hole, before pulling the license plate hanger away from the bike.

Remove the rubber gasket, as this is no longer required.

With the OEM license plate hanger on the bench, remove the reflector by carefully prising off the
spring clips, allowing access to the bolt heads behind. Remove the nuts off the two bolts, along
with the button head bolt, as shown in picture 2.

Remove the two bolts that secure the indicators in place, as shown in picture 3.

Carefully pull the two pieces of the licence plate hanger away from one another, giving access to
the electrical connections within, as shown in picture 4.

Disconnect the four connectors for the indicators. It is advisable to mark on the connectors left and
right, to make refitting easier.

The indicators can now be removed from the licence plate hanger by feeding the wires out through
the mounting hole.

Take the R&G Licence Plate Bracket (item 1 – TB0133 Part 1) and fit the Licence Plate Bracket
Cross-Brace (item 7 – TB0133 Part 3), using 2x M4 x 6mm long button head bolts (item 8). Ensure
these are screwed through the cross brace and into the thread on the licence plate bracket, as shown
in picture 5. We advise the use of a small amount of thread-lock on these bolts.

Fit the R&G license plate illuminator (item 11), as shown in picture 6. Use a small amount of
superglue to stick the light shroud in position. Feed the wiring through the hole in the cross brace
and up through the 10mm hole in the mounting face.

To connect the R&G licence plate illuminator (item 11), the wires will need to be "cut and shut" in
order to re-use the connectors to connect to the original wiring loom, via the OEM connector, as
shown in picture 7. To do this, cut the wiring of the OEM illuminator between the light and
connector, and fit a pair of bullet connectors that are supplied with the R&G illuminator to the
exposed ends of the wires that remain connected to the OEM connector. The R&G licence plate
illuminator can now be connected to the OEM connector. Plug it into the loom to check at this
stage (if illumination fails, swap the bullet connections around). (Please use the heatshrink (item
15) to protect the new license plate illuminator wires).

Fit the indicators of choice (original or R&G Mini Indicators (RG370) to the license plate bracket
(item 1) as shown in pictures 8 & 9. To fit the OEM indicators, feed the cable through the hole and
locate the rubber mount, then fit one M6 x 16mm long button head bolt (item 16), with a M6
washer and M6 nyloc nut on the back, before tightening. If fitting the R&G Mini Indicators, insert
the indicator stalk through the larger of the two holes and fit the nut on the exposed thread, as
shown in picture 9. In the remaining hole, position the rubber bungs (item 10) and push into place.

Feed the wires through the hole in the cross brace and up through the mounting face hole (if using
R&G Mini Indicators, the OEM indicator wiring will need to be "cut and shut" in order to re-use
the connectors to connect the R&G Mini Indicators to the wiring loom) This is done by cutting the
connectors off the OEM indicators, before fitting the bullet connectors (item 9 – CON0004) to the
exposed wiring and connecting to the R&G indicators. Plug it into the loom to check at this stage
(if illumination fails, swap the bullet connections around). (Please use the heatshrink (item 15) to
protect the new indicator wires).

Cable-tie the wires neatly together on the underside of the tail tidy. The self-adhesive cable clips
can also be used, positioned either side to keep the wires neat, as shown in picture 10.

Now the tail tidy assembly is ready to be offered up to the bike.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
R&G Racing
www.rg-racing.com Email: info@rg-racing.com