R&G LP0133BK Mode D'emploi page 6


Take the profiled spacer (item 2 – S0589) and offer up to the mounting points under the tail.
Ensure this spacer fits around the collars, before offering up the tail tidy assembly, whilst feeding
the wires though the hole in the plastic and up into the rear subframe.

Fit one of the M6 x 30mm long button head bolts(item 3) through the top mount of the tail tidy
assembly and through the collar within the rear subframe mount, before fitting a M6 washer and
M6 nyloc nut to the exposed thread. Tighten a few turns to hold the tail tidy assembly in place, as
shown in picture 11.

Take the remaining three M6 x 30mm long button head bolts, and locate through the licence plate
bracket cover (item 6 – TB0133 Part 2, before feeding through the tail tidy assembly and rear
subframe collars. Then fit one M6 washer and M6 nyloc nut to the exposed thread of each bolt, as
shown in picture 12.

Loosely tighten all 4 bolts, ensuring they are tightened evenly and gently clamp up on the profiled
spacer. Ensure no wires have become trapped before tightening each bolt (do not overtighten – the
nyloc nuts will keep the tail tidy secure).

Refit the connectors to the main wiring loom, as shown in picture 13.

Ensure the wiring is neat inside the bike, before re-connecting the wiring connector to the main
loom. It is a good idea to check the correct operation of the indicators and lights at this stage.

Refit the pillion seat unit and licence plate (it may require drilling).

IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON THE
LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE HITTING THE
BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD. IT IS YOUR
RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING ACTION. FAILURE TO
CHECK THIS COULD RESULT IN SERIOUS INJURY.

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the license plate illuminator and all lights before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its
particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any
fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable
condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc.
P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued
products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 14/12/12 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com Email: info@rg-racing.com