Areas Of Use; Filling With Petrol - Stiga VILLA ROYAL Mode D'emploi

All manuals and user guides at all-guides.com
2.4.11 Power take-off (3,4:F)
(Royal, de Luxe)
Switch for engaging/disengaging the electromag-
netic power take-off for operating front-mounted
accessories. Two positions:
1. Press the front part of the switch – the
power take-off is engaged. The symbol
will light up.
2. Press the rear part of the switch – the
power take-off is disengaged.
2.4.12 Cutting height adjustment (4:J)
(Royal)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (6:Z).
2.4.13 Clutch release lever (7:L)
A lever for disengaging the variable transmission.
Enables the machine to be moved by hand without
the help of the engine. Two positions:
1. Lever out – transmission en-
gaged for normal operation.
There is an audible click when
the lever locks in the outer posi-
tion.
2. Lever in – transmission disen-
gaged. The machine can be
moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
2.4.14 Seat (8:M)
The seat can be folded and adjusted for-
wards and backwards. The seat's forward/
backward position can be locked with the
knobs (8:N).
The seat is equipped with a safety switch that is
connected to the machine's safety system. This
means that certain activities that can entail danger
cannot be carried out when nobody is sitting in the
seat. See also 4.3.2.
2.4.15 Engine casing (9:O, 10:O)
To inspect and maintain the engine and battery, re-
move the engine casing.
The engine must not be running when the cas-
ing is removed.
Dismantling:
1. Fold up both casing locks at the rear edge (9:P).
2. Pull the engine casing back a little first. Then lift
it off.
Assembly:
ENGLISH
1. Fold the seat forward.
2. Align the casing's upper, front pins with the
slots in the front engine casing (10). Leave ap-
prox. 2 cm clearance.
3. Guide both conical side pins into the holes in the
front engine casing. Then press the entire casing
forwards.
5. Finally fold down both casing locks (9:P).
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.

3 AREAS OF USE

The machine may only be used for the following
tasks using the genuine STIGA accessories stated.
Work Accessories, STIGA genuine
Mowing Using mowing decks:
85 M, 92 M, 107 M (Royal), 107
M El (Royal)
Sweeping Using brush unit or collector
brush unit. The use of a dust
guard is recommended with the
first option.
Snow clearance Using snow blade or snow
thrower Snow chains and frame
weights are recommended.
Grass clipping and Using towed collector 30" or
leaf collection 42".
Grass and leaf Using dump cart Standard.
transport
The maximum vertical load on the towing hitch
must not exceed 100 N.
The maximum over-run load on the towing hitch
from towed accessories must not exceed 500 N.
NOTE! Before using a trailer – contact your insur-
ance company.
NOTE! This machine is not intended to be driven
on public roads.
4 STARTING AND OPERATION
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.

4.1 Filling with petrol

Always use lead-free petrol. You must never use 2-
stroke petrol mixed with oil.
The tank holds 14 litres. The level can easily be
read through the transparent tank.
EN
55