Decommissioning, Dismantling And Disposal - Group Dynamics WRM 8 Instructions Pour L'installation Et Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
service or by qualified personnel.
BEFORE ANY MAINTENANCE
OPERATION, CHECK THAT THE WALL
CUTOFF SWITCH IS OFF AND THE
WARM WATER, COLD WATER AND
STEAM TAPS ARE CLOSED (THE
LATTER APPLIES TO STEAM-HEATED
MACHINES ONLY). THE DRUM MUST
BE STILL AND DRAINED AND THE
INSIDE TEMPERATURE MUST NOT
EXCEED 40°C.
Be very careful during maintenance. NEVER
override or ignore safety devices for any
reason. Use only original spare parts. If
doubts should arise, contact your sales person
immediately, explaining what the fault is
and indicating some information on the
machine: model and serial number (details
reported on the rating plate appearing on the
rear of the machine or inside the door, where
applicable).
MONTHLY CHECKS
Clean the filters located on the outer part of
the electrical valves.
Make certain that the steam valve strain is
clean (this applies to steam-heated machines
only).
Clean the soap dispenser from any soap
remains.
Clean the door gasket and the tub inlet with
a cloth.
YEARLY CHECKS
Make certain that the floor fastening nuts are
securely closed.
Check the wear of the belts and replace them
if necessary. If more than one of them is
worn out, replace the entire set of belts.
Make sure that the safety devices are working
properly (e.g. the door microswitch).
Make certain that the power connecting
screws are tight on the contactors and on the
power supply terminal board.
Disassemble the drain valve and clean it
inside from lint.
Check that the heaters are in perfect condition
and clean them from scale.
BEFORE TURNING THE MACHINE
BACK ON BY THE WALL CUTOFF
SWITCH, PUT ALL THE PANELS
REMOVED BACK IN PLACE.
AUTOMATIC MAINTENANCE
REQUEST
The machine keeps count of the number of
cycles it executes. After 1000 programs the
machine will flash a writing from cycle 1001
onwards.
More precisely, when starting a new cycle,
the machine will flash the writing "10 00 C"
for 10 seconds as the START button is
pressed, then it will carry out the selected
cycle normally.
When this message is displayed, request
yearly maintenance.
To call off this reading and start the 1000
cycle count from scratch, press the "DOWN"
push-button.
8.5 IDENTIFYING AND ORDERING
SPARE PARTS
To identify the codes of spare parts refer to
the exploded drawings and relevant list.
Once you have identified your codes, send a
standard written order to the manufacturer,
mentioning clearly machine model, serial
number, feed voltage and frequency and, of
course, including the code and description
of the spare part needed.
9. SUGGESTIONS FOR
DECOMMISSIONING,
DISMANTLING AND DISPOSAL
If the washing machine is no longer to be
used, it is advisable to put it out of service
and suitably dispose of the resulting
materials, considering the information
provided in chapter 3. For the sake of the
environment, sort the materials in accordance
with the waste disposal provisions in force
in your country, so that they can be properly
disposed of or recycled. All the parts
composing the machine can be treated as
solid urban waste, except for the metal parts,
which yet are not classed among special
waste in most European countries.
INFORMATION TO USERS
Pursuant to article 13 of law decree 25 July
2005, nr. 151 relating to "Implementation
of Directives 2002/95/EC, 2002/96/EC and
2003/108/EC concerning the reduction in
the use of hazardous substances in electric
and electronic apparatus, as well as waste
disposal"
The deleted dustbin symbol on the appliance
indicates the product must be disposed of
separate from other wastes once it reaches
the end of its life cycle.
Once the appliance has reached the end of its
life cycle, the user must therefore take it to a
suitable pre-sorted waste centre for electronic
and electro-technical appliances, or return it
to the dealer on purchasing a new similar
appliance, on a one for one basis.
Adequate pre-sorted waste collection before
subsequently sending the appliance for
recycling, treatment and environmentally
compatible disposal helps avoid possible
negative effects on the environment and
health and favours the recycling of the
materials making up the appliance.
Unlawful disposal of the product by the user
is punishable by the administrative sanctions
indicated in law decree nr. 22/1997 (article
50 and following articles of law decree nr.
22/1997).
22