Group Dynamics WRM 8 Instructions Pour L'installation Et Mode D'emploi page 19

www.groupdynamics-laundry.com
sales@groupdynamics.lv
reminder for the user. It is meant to assist
him in the selection of the most appropriate
cycle.
When the desired type has been selected,
confirm pushing "ENTER" and exit by the
"MODE" key.
Caution! This selection does not alter cycle
execution in the least. It is only a reminder
for the user.
COPY FROM AND COPY TO
Move to the "COPY FROM" or "COPY
TO" field using the "UP" and "DOWN"
keys. Press "ENTER" to confirm.
Select the program you wish to copy from or
to using the "UP" and "DOWN" keys. Press
"ENTER" to confirm.
The programmer will next prompt "COPY?".
Press "ENTER" to copy between cycles or
programs or press "MODE" to cancel.
Whether you chose to confirm or cancel the
copy, press "MODE" to exit.
DESCRIPTION OF PROGRAMMABLE
FUNCTIONS
Machine parameters are those required to
effect marginal changes to the wash programs
without having to access cycle or step
programming.
These functions enable the user to override
existing actions or add new ones in a wash
cycle. This does not alter the program features
in a radical manner, though.
The "MACHINE PARAMETERS" menu is
accessed as follows:
Open the washer door: all programming
actions must be performed with the door
open. The programming environment cannot
be accessed when the door is closed.
Hold down the "MODE" key until the
"MACHINE PAR." reading appears. Press
"ENTER" to confirm.The display will then
read the following items:
COOL
SPIN
PREWASH
DELAYED START
BUZZER
HEATING
ENABLE
The various items are described below.
These functions affect only the currently
selected wash cycle and remain effective
until they are disabled.
Cooling
Cool: This function decides whether the
wash bath is to be cooled right before it is
drained off. As a rule, cooling is aimed to
prevent the garments from undergoing a
thermal shock as they go, for example, from
a 90°C wash step to ambient temperature
rinsing.
Select "COOL" using the "UP" and "DOWN"
keys.
Confirm the selection by pushing "ENTER".
Programs/cycles and their respective
prewash setting can be scrolled using the
"UP" and "DOWN" keys. Move to the
desired cycle and press "ENTER". Then
choose between "YES" and "NO" using the
"UP" and "DOWN" keys and press
"ENTER" to confirm.
Press "MODE" to exit.
Short spinning
Spin: This function
acknowledge the standard-selected spinning,
reduce it to one-minute spinning or eliminate
it altogether. Select "SPIN" using the "UP"
and "DOWN" keys.
Confirm the selection by pushing "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle
and press "ENTER". Then again using the
"UP" and "DOWN" keys choose among:
NORMAL
REDUCED
NO SPINNING
Press "ENTER" to confirm.
Normal: the machine carries out standard
final spinning. The machine carries out
standard final spinning.
Reduced: one-minute final spinning.
Spinning length is applied to the last spinning
speed. The acceleration ramp is never
reduced.
No spinning: final spinning is not carried
out.
Press "MODE" to exit.
No prewashing
Prewash: Generally speaking, all programs
include prewash. The purpose of this function
is actually to override prewash. This is
especially useful when handling laundry
that is not heavily soiled.
Select "PREWASH" using the "UP" and
"DOWN" keys.
Confirm the selection by pushing "ENTER".
Programs/cycles and their respective
prewash setting can be scrolled using the
"UP" and "DOWN" keys. Move to the
desired cycle and press "ENTER". Then
choose between "YES" and "NO" using the
"UP" and "DOWN" keys and press
"ENTER" to confirm.
Press "MODE" to exit.
Deferred cycle start
Delayed START: This function defers
machine start up to a maximum of 24 hours.
As soon as the scheduled time has elapsed
the machine starts automatically. When
waiting for the deferred start the machine
reads the countdown. If during the
countdown the "START" key is pressed, the
machine immediately starts the cycle that
was originally selected.Select "DELAYED
START" using the "UP" and "DOWN" keys.
Confirm the selection by pushing "ENTER".
The parameter status, i.e. either
"DISABLED" or "ENABLED" will appear.
Press "ENTER" to change the selection. Use
the "UP" and "DOWN" keys to make your
selection in minutes and/or hours and then
press "ENTER" to confirm.
Press "MODE" to exit.
As soon as the "START" key is pushed the
countdown starts and the display reads the
following message:
19
Start scheduled in:
countdown (time remaining to the beginning
of the cycle)
CAUTION:
When pressed, the START key excites the
CYCLE relay and the door is automatically
allows to
locked.
If the door is not closed correctly, the "door"
alarm will warn the user. If the door fails to
be locked, alarm "E6" trip.
In the latter case it will be necessary to
proceed as follows: press START once, solve
the problem (if possible) and press START
once again to set the machine to work.
If a deferred start is cancelled (by entering
the programming mode and setting F4 to
00.00) the door will be automatically
unlocked.
Enable/disable BUZZER
Buzzer: Each time a key is pressed the buzzer
gives out a short loud beep. This can be
eliminated by accessing this function.
Select "BUZZER" using the "UP" and
"DOWN" keys.
Confirm the selection by pushing "ENTER".
The parameter status, i.e. either
"DISABLED" or "ENABLED" will appear.
Press "ENTER" to change the selection. Use
the "UP" and "DOWN" keys to make your
selection and then press "ENTER" to
confirm.
Press "MODE" to exit.
Changing heating temperature
Heating: The maximum wash bath
temperature reached through heating in any
cycle can be lowered by 10°C. Select
"HEATING" using the "UP" and "DOWN"
keys.
Confirm the selection by pushing "ENTER".
The parameter status, i.e. either "NORMAL"
or "REDUCED" will appear. Press "ENTER"
to change the selection. Use the "UP" and
"DOWN" keys to make your selection and
then press "ENTER" to confirm.
Press "MODE" to exit.
Enabling cycles
Enable: When one or more cycles are not
desired, it is possible to hide them from the
available alternatives. This means that they
are not erased but only concealed from the
user interface menu. The enabled cycles can
be scrolled using the "SELECT" and "UP"
or "DOWN" keys and the disabled cycles
will not be listed.Select "ENABLE" using
the "UP" and "DOWN" keys.
Confirm the selection by pushing "ENTER".
Programs/cycles and their respective cooling
setting can be scrolled using the "UP" and
"DOWN" keys. Move to the desired cycle
and press "ENTER". Again using the "UP"
and "DOWN" keys, choose between
"ENABLED" and "DISABLED" and press
"ENTER" to confirm.
Press "MODE" to exit.
PROGRAMMIMG BY PC
Washers can also be programmed via PC,
through a serial port. For this purpose the