Monitoring The Brush Resistance; Setting The Cycle Time; Explanation Of The Display Indications - Kerbl MaxiSwing 18860 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19

6.3.1 Monitoring the brush resistance

The unit monitors the current used by the motor and therefore checks the correct functioning of the cattle brush. If the gear motor is placed under
too much strain, the brushes stand still and then move in the opposite direction. This can occur if the animals lean to far too one side or if a tail
gets wound up in the mechanism.
If this event is repeated several times without the unit having run properly in between, the unit first goes into an alarm state for a few minutes
and does not start during this time. If the load on the motor is not lower even after this pause, then the fault message "A03" is triggered after
further load cut-offs and the unit no longer starts.
The cut-off resistance can be set using the dip switch element (see table under 6.3.2) on the PCB. The cut-off resistance is lowest at the F1 setting
and highest at F15. The default setting and therefore the best setting for the Cow Cleaning Machine MaxiSwing is F8.

6.3.2 Setting the cycle time

The cycle time is set at the factory to 60 seconds. If necessary, this can be adjusted using the dip switch element on the circuit board
(Fig. 8 - item 1) to a value between 7.5 and 300 seconds. The cycle time may only be readjusted after consultation with Kerbl Service.
The default setting and therefore the ideal setting for the Cow Cleaning Machine MaxiSwing is T3.
1 - 5
Machine type
Cut-off resistor
1
2
3
1
4
2
5
3
6
4
7
5
8
F F 1 1
F F 1 1
F F 2 2
F F 2 2
F F 3 3
F F 3 3
F F 4 4
F F 4 4
F F 5 5
F F 5 5
F F 6 6
F F 6 6
F F 7 7
F F 7 7
F F 8 8
F F 8 8
Once the unit has been restarted (connected to the power supply), the dip switch changes will take effect and the settings will be briefly shown
on the display.

6.3.3 Explanation of the display indications

Description of display messages:
Display indication Description
No display
No mains voltage present
---
Unit ready for operation
A00
Undervoltage
A01
Overvoltage
A02
Maximum running time exceeded - control unit has not switched off for 20 minutes (sensor faulty/incorrectly set)
A03
Brushes blocked repeatedly
6 - 9
10 - 12
Cycle time
6
9
7
10 11 12
8
9
10 11 12
T T 1 1 – – 1 1 0 0 s s e e c c
T T 1 1 – – 1 1 0 0 s s e e c c
T T 2 2 – – 2 2 0 0 s s e e c c
T T 2 2 – – 2 2 0 0 s s e e c c
T T 3 3 – – 6 6 0 0 s s e e c c
T T 3 3 – – 6 6 0 0 s s e e c c
T T 4 4 – – 9 9 0 0 s s e e c c
T T 4 4 – – 9 9 0 0 s s e e c c
T T 5 5 – – 1 1 2 2 0 0 s s e e c c
T T 5 5 – – 1 1 2 2 0 0 s s e e c c
T T 6 6 – – 1 1 8 8 0 0 s s e e c c
T T 6 6 – – 1 1 8 8 0 0 s s e e c c
T T 7 7 – – 2 2 4 4 0 0 s s e e c c
T T 7 7 – – 2 2 4 4 0 0 s s e e c c
T T 8 8 – – 3 3 0 0 0 0 s s e e c c
T T 8 8 – – 3 3 0 0 0 0 s s e e c c
1 - 5
6 - 9
Machine type
Cut-off resistor
1
2
3
1
4
2
5
3
6
4
7
5
8
F F 9 9
F F 9 9
F F 1 1 0 0
F F 1 1 0 0
F F 1 1 1 1
F F 1 1 2 2
F F 1 1 3 3
F F 1 1 4 4
F F 1 1 5 5
F F 1 1 5 5
45
10 - 12
Cycle time
Table:
Dip switch element
setting on the board
6
9
7
10 11 12
8
9
10 11 12
F F 1 1 1 1
F F 1 1 2 2
F F 1 1 3 3
F F 1 1 4 4

Publicité

Table des Matières
loading

Table des Matières