Truma Trumatic C 6002 EH Mode D'emploi page 14

Technical data
termined in accordance with EN 624 or Truma test conditions
Type of gas:
Liquid gas (propane/butane)
Operating pressure:
30 mbar
Water contents:
12 litres
Heating up time from approx. 15°C to approx. 60°C:
Summer-/gas operation: approx. 30 minutes
(measured according to EN 15033)
Summer-/electrical operation (1800 W): approx. 45 min.
Winter mode: approx. 60 min. upward
(depending on the heat output)
Water pressure:
max. 2.8 bar
Rated thermal output:
Liquid gas: 2000 W, 4000 W, 6000 W
Electrical: 900 W, 1800 W
Gas consumption:
170 – 480 g/h
Air delivery volume:
max. 287 m³/h (free-blowing without warm-air duct)
Current input at 12 V:
Heater + water heater: 0.2 – 5.6 A
Heating up of water heater: 0.4 A
Stand-by: 0.001 A
Current input of electrical safety/drain valve at 12 V:
0.035 A
Current input of 230 V:
900 W (3.9 A) or 1800 W (7.8 A)
Weight:
approx. 18.7 kg (without water contents)
Declaration of conformity :
The Trumatic C 6002 EH has been tested by the DVGW and
complies with the gas equipment directive (90/396/EEC) and
the other applicable EC directives. The following CE Product
Ident. No. is available for EU countries:
CE-0085AS0122.
The heater complies with heater directive 2001/56/EC and supple-
ments 2004/78/EC and 2006/119/EC and bears the type approval
number:
e1 00 0146.
The heater complies with vehicle engine interference suppres-
sion directive 72/245/EEC with supplements 2004/104/EC and
2005/83/EC, and bears type approval number:
e1 03 2499.
The heater complies with EMC directive 89/336/EEC and low
voltage directive 73/23/EEC.
The right to effect technical modifications is reserved!
14
Manufacturer´s terms of warranty
1. Case of warranty
The manufacturer grants a
warranty for malfunctions
in the appliance which are
based on material or produc-
tion faults. In addition to this,
the statutory warranty claims
against the seller remain
valid.
A claim under warranty shall
not pertain:
– for parts subject to wear
and in cases of natural
wear and tear,
– as a result of using com-
ponents in the units that
are not original Truma parts
and using unsuitable gas
pressure regulators,
– as a consequence of failure
to respect Truma instruc-
tions for installation and
use,
– as a consequence of
improper handling,
– as a consequence of im-
proper transport packing,
not arranged by Truma.
2. Scope of warranty
The warranty is valid for
malfunctions as stated under
item 1, which occur within
24 months after conclusion
of the purchase agreement
between the seller and the
final consumer. The manufac-
turers will make good such
defects by subsequent fulfil-
ment, i.e. at their discretion
either by repair or replace-
ment. In the event of manu-
facturers providing service
under warranty, the term
of the warranty shall not re-
commence anew with regard
to the repaired or replaced
parts; rather, the old warranty
period shall continue to run.
More extensive claims, in
particular claims for compen-
satory damages by purchas-
ers or third parties, shall
be excluded. This does not
affect the rules of the product
liability law.
The manufacturer shall bear
the cost of employing the
Truma customer service for
the removal of a malfunction
under warranty – in par-
ticular transportation costs,
travelling expenses, job and
material costs, as long as the
service is carried out in Ger-
many. The warranty does not
cover customer service work
in other countries.
Additional costs based on
complicated removal and
installation conditions of the
appliance (e.g. removal of
furniture or parts of the vehi-
cle body) do not come under
warranty.
3. Raising the case of
warranty
The manufacturer's address
is:
Truma Gerätetechnik
GmbH & Co. KG,
Wernher-von-Braun Straße 12,
85640 Putzbrunn.
In Germany, always notify
the Truma service centre if
problems are encountered; in
other countries the relevant
service partners should be
contacted (see list of ad-
dresses). Any complaints are
to be described in detail. In
addition, the properly com-
pleted guarantee certificate
is to be presented, or the fac-
tory number of the unit and
the date of purchase given.
In order for the manufactur-
ers to be able to determine
whether an incident subject
to guarantee has occurred,
the end user must, at his own
risk, bring the device to the
manufacturers or send it to
them. If there is damage to
heaters (heat exchangers),
the gas pressure regulator
must also be sent back to the
factory.
In instances of the device
being sent to the works,
dispatch is to be effected by
freight transport. In cases
under guarantee, the works
shall bear the transport costs
or the costs of delivery and
return. If the damage is
deemed not to be a warranty
case, the manufacturer shall
notify the customer and shall
specify repair costs which
shall not be borne by the
manufacturer; in this case,
the customer shall also bear
the shipping costs.