CASCO PF 1000 Mode D'emploi page 7

HEAD SIZE ADJUSTMENT
The head ring (Fig. 3.1/3.2) can be adjusted to the correct head size by means of the 4 adjustable pin set-
tings in the left/right temple area and the Vario-Disk-fit™ turning clasp in the neck (Fig. 3.3). For the size
spectrum: 52–64 cm only one helmet shell size is needed.
Fig. 3.1
By placing the pin in the front opening, the size is reduced, by placing the pin in the back opening, the size is
enlarged. Helmets are delivered ex-factory in the mid-size position.
Fig. 3.3
NECK HEIGHT ADJUSTMENT
The neck cushion height is also adjustable. By light-
ly applying excess pressure whilst pushing the neck
cushion up or down, the neck cushion height can be
more comfortably re-positioned (Fig.4).
Fig. 4
NECK STRAP ADJUSTMENT
This is a one-off adjustment to be carried out before initial wear. Adjust the length of the strap above the ad-
justment mechanism (metal slide buckle), until the strap is comfortably positioned against the neck without
covering the ear (Fig. 6.1-6.2). The strap is fed through the back of the helmet by means of diffuser from
within. By pulling down on the left or right strap section, the strap length can be evenly regulated (Fig. 6.3).
Fig. 6.2
Fig. 6.1
12
Fig. 3.2
Turn the dial lock anti-clockwise
until the head band is fully open.
Put the helmet on and turn the dial
lock clockwise until the helmet is
sitting comfortably and firmly (Fig.
3.3).
FOREHEAD ADJUSTMENT
The whole of the front section of the two-part head
ring can be released and re-adjusted up or down
according to head size and forehead shape (Fig. 5).
Fig. 5
Fig. 6.3
CARRYING HEIGHT ADJUSTMENT
Push up
or down
The catches slip
through beneath
Press in
the retainer
7
Fig.
The carrying height can be altered by pressing the two „fingers" together in the back section (under the Nomex
cloth). The front section can be adjusted by means of the Velcro strap on the bottom edge of the carrying net.
ADJUSTING THE CHIN STRAP
Fasten the strap with the buckle (Fig. 2/13) and regulate the length using the free end of the strap. The PF 1000
series fulfils the requirements of the standard DIN EN 443:2008 in respect of the retention system provided that
the chin strap supplied by the manufacturer is worn and adjusted in accordance with the regulations.
Attention! The protective effect is only achieved when the helmet is ideally positioned, the head band adapted
to the head girth and the chin strap fastened. Only wear the helmet when it is fully assembled.
Fig. 8.1
SERVICE LIFE
The helmets have a maximum service life with no binding expiry date. The service life of these helmets is
influenced by the environment and environmental conditions in which the helmet is used and stored, as
well as the materials used in its construction. This CASCO PF 112 firefighting helmet series is equipped
with an extremely temperature resistant coated shell of highly compressed fiberglass which offers out-
standing durability and is not affected by sunlight (UV rays).
The service life of these helmets is mainly limited by mechanical, thermal and chemical factors. The highly
compressed fibreglass is generally held to be extremely durable against such pressures. The helmets'
load capacity when faced with weather-related, chemical and thermal factors, shows a considerably
better performance than thermoplastic materials.
Warning: The CASCO PF 1000 helmet series does not have a binding discard or expiry date, the maximum
service life is dependent on the above-mentioned factors.
In order to achieve a long service life, the instructions for use must be applied. This especially covers cleaning
and maintenance, care and repair measures and advice on how to carry out regular damage checks. Please
note: Every helmet equipped with interior construction and accessories must be checked for possible dam-
age before and after every use and these checks be documented. If these prerequisites have been fulfilled
and the helmet shows no indication of mechanical, thermal or chemical damage and if all instructions for use
have been followed, CASCO PF 1000 series firefighting helmets can easily be worn for longer than 15 years.
Leave in the
desired position
Fig. 8.2
13