Fitting The Gr. 1 Car Seat Using The Rigid Connectors And The Car's Three-Point-Belt (9-18 Kg) - Chicco Unico Plus Mode D'emploi

• Run the abdominal portion of the belt along
the blue guide (P) (Fig. 26) run the diagonal
portion of the car seat belt through the top
guide (T), along the path between the head-
rest and the seat following the indicated seat
belt guide (Fig. 27).
• Fasten the belt to the buckle (Fig. 28).
• Put the mini reducer cushion back in place
(0-6 kg).
• The final configuration of the car seat must
match Fig. 29.
The mini reducer cushion is to be used from
birth up to 6 kg.
Once installation is complete place the baby in
the seat as follows:
• Press the belt adjustment button (O) and
hold and pull both the car seat belts toward
yourself until the maximum length is reached
(Fig. 30).
• Unbuckle the car seat belts by pressing the
button on the buckle (Fig. 31).
• Place the baby in the car seat with care, join
the two buckle tongues and fasten them
once again (Fig. 32).
• Using the appropriate lever (S), adjust the
height of the headrest, so that the belts exit
at the height of the baby's shoulders (Fig. 33).
• To adjust belt tightness, pull the adjustment
strap (N) upwards with caution until the belt
is suitably tight (Fig. 34).
To remove the car seat, unhook the car seat
belts and the rigid connectors (C) by pushing
the release buttons (D).
2.3 FITTING THE GR. 1 CAR SEAT USING
THE RIGID CONNECTORS AND THE
CAR'S THREE-POINT-BELT (9-18 KG)
In the Group 1 configuration, the car seat must
ALWAYS be front-facing, and must ALWAYS be
installed using the rigid connectors and the
car's 3-point seat belt.
WARNING! Use the reclined car seat in the
positions 1, 2 or 3. NEVER use position R.
• Use the lever (M) to rotate the seat 180°,
verifying that it has locked in the front-facing
position (Fig. 35).
• Position the car seat on the seat of the vehicle
in the front-facing direction.
• Pull the rigid connectors out completely (C),
by using the button (D) (Fig. 36).
• Fasten the connectors to the hooks present
between the backrest and the seat (Fig. 37).
Once fastening occurs, you will hear a typical
"click" and the indicator will change from red
to green.
• Run the diagonal portion of the belt along
the top belt guide (T). Insert the three-point
belt in the belt slot (U) and have it exit from
the slot on the opposite side (Fig. 38)
• Buckle the car's seat belt (Fig. 39)
• Push the car seat firmly against the backrest
of the vehicle seat to ensure the best fit (Fig.
40) and tighten the diagonal portion of the
belt (Fig. 41).
Once installation is complete place the baby in
the seat as follows:
• Press the belt adjustment button (O) and
hold and pull both the car seat belts toward
yourself until the maximum length is reached
(Fig. 42).
• Unbuckle the car seat belts by pressing the
button on the buckle (Fig. 43).
• Place the baby in the car seat with care, join
the two buckle tongues and fasten them
once again (Fig. 44).
• Using the appropriate lever (S), adjust the
height of the headrest, so that the belts exit
at the height of the baby's shoulders (Fig. 45).
• To adjust belt tightness, pull the adjustment
strap (N) with caution until the belt is suitably
tight (Fig. 46).
2.4 CHANGING THE CONFIGURATION OF
THE CAR SEAT FROM GROUP 1 (9-18
KG) TO GROUP 2/3 (15-36 KG)
To change the configuration from Group 1 to
Group 2/3 you will need to complete the fol-
lowing steps:
• Loosen the belts on the car seat completely
by pressing the adjustment button (O) (Fig.
47).
• Use the lever (S) to set the maximum exten-
sion possible for the headrest (Fig. 48).
• Free the car seat belts from the anchor (Fig.
49A) and place the anchor in the appropriate
housing (Fig. 49B).
• Run the car seat belts through the holes and
free them from the buckle (Fig. 50).
28