Cleaning And Maintenance; Carrying Handle - Chicco SCOOP Mode D'emploi

reduced to less than 140mm when the
mattress is in position;
• The matress purchased separately
should conform to BS 1877 : Part 10.

CLEANING AND MAINTENANCE

Cleaning
Clean the fabric parts with a damp sponge and
neutral detergent. Please refer to the product's
care label.
Routinely wipe clean plastic parts with a soft
damp cloth.
Always dry the metal parts to prevent the forma-
tion of rust if the carrycot has come into contact
with water.
Maintenance
Lubricate the moving parts only if necessary, with
a light application of a silicone based lubricant.
Always dry the metal parts to prevent the for-
mation of rust. Do not submerge the carrycot in
water. Routinely wipe clean plastic parts with a
soft damp cloth. To avoid friction, ensure that the
locking devices of the carrycot and pram are free
from dust or sand. Do not leave the product ex-
posed to the sun for a long period of time; it may
cause the fabric to fade.
CARRYCOT FEATURES
HOOD
The carrycot is equipped with a sun canopy and
windbreaker that can be adjusted to various posi-
tions.
MOUNTING AND REMOVAL
1- Check that the clips located on the end of the
metal arch are properly fastened to the but-
tons located on the fabric part. The buttons are
properly fastened if the two ends of the metal
arch (fi g 1) are easily visible.
2- Insert the two metal ends in the B and C sup-
ports located in the central part of the carrycot
until you hear a click (fi gure 2A); fasten the four
tabs of the rear arch (fi gure 2 B).
NB: The coupling system is located inside the
plastic B and C supports, the round button on the
supports serve only for removing the hood (see
point 3).
3- To remove the hood, fi rst pull out the 4 tabs of
the rear arch (fi gure 3A) and then remove the
front arch by pushing the two buttons located
on the base of the locking device (fi g. 3B).
WARNING: Improper removal of the hood could
result in the tabs breaking.
HOW TO USE THE HOOD
4- Inside the hood, between the visor and the fi rst
segment, is a fabric ring that can be used for
hanging soft toys. It comes with handy hooks
(fi gure 4 A).
Warning- only use toys that have the following
Chicco codes: 71328, 71329, 71330.
There is an adjustable rear opening fl ap to guar-
antee proper ventilation: Unzip it to open, and
fold the fabric panel on the upper part of the
hood. (Figure 4B).
INTERNAL COVERING AND COVER
5- To fasten the internal covering to the carrycot:
Slip the plastic band located in the baby's
head zone between the styrofoam support
and the body of the carrycot; then fasten the
two tabs in the baby's foot area under the
edge of the carrycot, as shown in fi gure 5A.
Then fasten the two lateral press studs and
fasten the two fabric strips with velcro in the
centre of the area where the baby's feet are
(fi gure 5 B).
The covering fastens by simply using the zi per.
Once mounted, both sides may be opened, or
on the top using the velcro opening (fi gure 5
C).
ADJUSTABLE BACKREST -
COMFORT SYSTEM
6- The backrest of the carrycot can be adjusted
gradually. To lift or lower the backrest use the
wheel located on the outer part of the carrycot
near the baby's feet (fi gure 6).
WARNING: It is advisable to ventilate the carrycot
after prolonged use.

CARRYING HANDLE

7- The carrycot comes with a comfortable car-
rying handle that can be adjusted in three po-
sitions (fi g. 7):
A) Transport
B) Middle
C) Rest
8- To put the handle in the vertical position, grasp
it in the centre and pull it upwards until you
hear a click (fi gure 8 A); to put the handle back
in the rest position press both buttons at the
16