In Case Of A Gas Leak; Getting The Appliance Ready For Use; Before Each Use; Before First Use (In A Long Time) - Barbecook SIESTA 310 Mode D'emploi

MAN_GAS_SIESTA_310_310_CREME_DE_BBC_151001_B.book Page 9 Thursday, October 1, 2015 6:36 PM
A
C
Your pressure regulator and coupling may be different
0
from the ones in the illustrations.
Do one of the following:
6
If you detect a leak, continue as described in " In case of
•
a gas leak".
If there are no leaks, close the gas supply, rinse all
•
components thoroughly with water and dry them well.

7.6 In case of a gas leak

Close the gas supply and do one of the following:
1
If you detected a leak on one of the connections, tighten
•
that connection.
If you detected a leak on the cylinder or hose, replace the
•
cylinder or hose.
Recheck the connection or component on which you
2
detected the leak.
If the leak is not repaired, contact a Barbecook dealer. Do
3
not use the appliance until the leak is repaired.
For a list of nearby Barbecook dealers, refer to
2
www.barbecook.com.
8 GETTING THE APPLIANCE READY
FOR USE

8.1 Before each use

Each time you use the appliance, make sure that:
The appliance is in an appropriate location. See "3.3 Select
•
an appropriate location".
The gas hose does not drag on the ground and cannot come
•
into contact with a hot surface or with dripping fat.
The bowl is clean. We recommend cleaning the bowl after
•
each use. See "11.2 Cleaning the bowl".
The burners and venturis are not blocked by insect nests or
•
spider webs. See "11.3 Cleaning the burners and venturis".
The burners are assembled correctly. The venturis have to
•
be placed over the openings of the gas valves.
B
2
D

8.2 Before first use (in a long time)

If you use the appliance for the first time or for the first time after
a long period of non-use, you have to execute some extra
checks:
•
•
1
•
•

8.3 Burning in the appliance

By burning in the appliance before the first use, you remove
remaining manufacturing greases from the appliance. Proceed
as follows:
1
2
3
4
9
0

9.1 Safety instructions

•
•
•

9.2 Lighting the main burners

9.2.1 U
1
2
www.barbecook.com
If you want to be absolutely sure that your gas connection
is okay, you can check your appliance on gas leaks before
each use. See "7 Checking for gas leaks".
Make sure that you have read, understood and checked all
the instructions in this manual (only before first use).
Check the appliance for gas leaks. See "7 Checking for gas
leaks".
Also check for gas leaks if your appliance was assembled
by your dealer.
Clean the burners and venturis (only before first use in a long
time). See "11.3 Cleaning the burners and venturis".
Burn in the appliance before you put any food on it (only
before first use). See "8.3 Burning in the appliance".
Light the main burners and set their control knobs to HIGH.
See "9.2 Lighting the main burners".
Close the lid and let the appliance burn for 15 minutes. Do
not put any food on the grill yet.
After 15 minutes, open the lid and let the appliance burn for
another 5 minutes (control knobs still set to HIGH).
After 5 minutes, the appliance is ready for use. You can now
put food on the grill.

LIGHTING THE BURNERS

To light the burners with the electrical igniter, you have to
install an AA battery in the igniter. That battery is not
supplied with the appliance. You find the battery case of
the igniter on the control panel of your appliance.
Before you light the appliance, execute all checks listed in

"8 Getting the appliance ready for use".

Make sure the lid is always open when you light a burner.
Never bend directly over a burner when lighting it.
SING THE IGNITER
Open the lid and set the control knobs of the main burners to
OFF.
If no other burner is lit yet, open the gas supply and wait ten
seconds. This allows the gas to stabilize.
9