Güde GWS 700 ZR HM-2 Traduction Du Mode D'emploi D'origine page 26

ENGLISH
22
Check all screw and plug-in connections and
protective equipment if firm and tightened
properly and whether all moving parts are
running smooth whenever the appliance is to be
put into operation.
The protective equipment on the appliance is
strictly prohibited to be disassembled, changed,
used in conflict with the designation and it is
prohibited to attach any protective equipment of
other manufacturers.
For cleaning and maintenance, the following
safety guards must be removed:: Additional safety
device for saw blade protection
After carrying out the work, all safety guards
must be reinstalled again correctly! See image
description.
The appliance must not be used if damaged
or safety equipment is defective. Replace any
worn-out and damaged parts.
Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
Before pressing On/Off, make sure the saw blade has
been fitted properly.
The saw must not be used any longer if the cradle
fails to automatically return to the rest position.
The saw must not be used any longer if the saw
blade fails to stop in 10 seconds after switching the
machine off.
For security, use devices such as safety- and pressure
device, guide slide, rip fence, etc.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
It is necessary to refrain from removing any cuttings
and parts of workpieces from the cutting area.
Do not use saw blades which are damaged or
deformed
Properly sharpened saw blades to be used only.
Follow instructions for use, adjustment and repair of
saw blades of manufacturers.
Do not use saw blades not corresponding to the key
data given in these instructions for use.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Only use tools that meet standard EN 847-1.
Transport and store the tools in a suitable receptacle;
To minimise noise production, the tool must be
sharpened and all elements for noise minimisation
(covers, etc.) must be properly adjusted.
Replace the table insert when worn
Familiarise with the safety procedures for cleaning,
maintenance and regular removal of sawdust and
dust to reduce the risk of fire.
Make sure the flange used is suitable for the given
purpose of use, as specified by the manufacturer.
Use only original accessories and original spare parts.
Handling equipment to be used only when handling
the machine. Make sure the device cannot roll away,
fall over or tip over with suitable fastening devices.
- Provide sufficient general or local lighting for the
work area.
- Observe the maximum speed indicated on the saw
blades.
- Ensure that the guards and other safety devices
necessary for operating the machine are in place, in
good working order and properly maintained.
- Operators must be adequately trained in the use,
adjustment and operation of the machine.
- Installation and major repair work may only be
carried out by specially trained personnel
Additional safety instructions for PTO-
operation
For tractors with hydraulic or air pressure switch
Power take-off shaft coupling must be a PTO shaft
with
freewheel can be used.
To rectify faults or remove
If a piece of wood is jammed, stop the machine,
switch off the tractor and remove the ignition key
pull out.
When leaving the workplace, pull the tractor
and remove the ignition key.
During transport the PTO operation must be switched
off
be.
The warning plate with rear light DIN 110030 must be
attached to
the saw is mounted and the rear light on the tractor
must be connected.
The saw may only be connected to tractors with
3-point linkage.
Category 1 and 2.
PTO shaft speed max. 540 min-1.
Direction of rotation of the PTO shaft counterclock-
wise.
The power take-off shaft is prevented from rotating
when operating with the chain
secure.
The universal joint shaft after uncoupling from the
tractor
hang on the retaining bracket.
Maintenance
Repairs and works specified in these Instructions
may only be performed by qualified authorised staff.
Use only original accessories and original spare parts.
If necessary, a list of spare parts can be found at
www.guede.com.
Carry out a visual inspection before switching the
appliance on.
At all times, keep the machine, ventilation slots, in