Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
No. Length
Nuber of
Overlapping Needle throw
(a)
stitches(n)
amount(b)
67
3.0
4
1.0
68
4.0
5
1.0
69
5.0
6
1.0
70
6.0
7
1.0
71
3.0
5
1.0
72
4.0
6
1.0
73
5.0
7
1.0
74
6.0
9
1.0
75
3.0
6
1.0
76
4.0
8
1.0
77
5.0
9
1.0
78
6.0
11
1.0
• Set the cut length to the length of the knife holder to be used plus overlapping amout (b) or more.
• Select the length (a) of the straight bar within the range where there is no interference of the throat
plate with the eyelet holding plate in consideration of the position of the presser plate when the
cloth open mechanism opened.
• When the length (a) of the straight bar is lengthened, needle thread may not be clamped unless the
lateral position of the needle thread clamp unit is re-adjusted. (Refer to the Engineer's Manual.)
(15) Number of stitches of the round bar
(16) Left side cut space compensation
No. Length
Nuber of
width(c)
(a)
stitches(n)
− 1.0
79
3.0
4
− 1.0
80
4.0
5
− 1.0
81
5.0
6
− 1.0
82
6.0
7
− 1.0
83
3.0
5
− 1.0
84
4.0
6
− 1.0
85
5.0
7
− 0.5
86
6.0
9
− 1.0
87
3.0
6
− 1.0
88
4.0
8
− 1.0
89
5.0
9
− 1.0
90
6.0
11
1) Set the number of stitches with [RIGHT
2) In case of without the round bar, set the value to "0".
3) In case of entering the round bar, 4 to 20 stitches
4) When the round bar has been set, the number of
Number of
stitches
Clearance
+
–
Overlapping Needle throw
amount(b)
width(c)
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
1.5
− 1.0
The number of stitches of the round bar
is set.
or [RIGHT
] key
can be set.
overlapped stitches of sewing start and sewing
end can be set with the number of stitches of
sewing end compensation of data No. 9.
The clearance where the knife drops in the left
side of the parallel section can be compensated.
Set the clearance with [RIGHT
] key
. If the setting is " ＋ ", the clearance
becomes larger than that on the right side, and if it is
" − ", the clearance becomes smaller.
Setting range is limited by the set value of the cut
space of No. 6.
Cut space setting range is -1.2 ≦ cut space +
compensation of left cut space ≦ 1.2.
Select the shape of straight
bar from the left-hand table.
a Length
n Number of stitches
b Overlapping amount
c Needle throw width
b
c
a,n
] key
.
] key
or [RIGHT
37
Publicité
Chapitres
Table des Matières
