Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
9a. screws, 4 screws total.
Rangehood Control Panel
The control panel is located in the center of the
hood bottom.
A
FIGURE 26
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking vapors
and odors from the cooktop area.
Rangehood Control Panel
The control panel is located in the center of the hood bottom. The
Light On/Off Button (A)
position and function of each control button are indicated in FIGURE
27
On/Off switch for the lights. Position "0" turns the
lights Off, turning the switch to the right is On.
Light On/Off Button (A)
On/Off switch for the halogen lights. Position "0" turns the lights off,
Blower On/Off Button (B)
turning the switch to the right one click is the dimmer position, and
On/Off switch for the blower. Move the dial to the
the next click to the right is full power
right to turn the blower ON and vary the speed of
Blower On/Off Button (B)
the blower. Turn to the left at "0" to turn it OFF.
On/Off switch for the blower. Move the dial to the right to turn the
blower ON and vary the speed of the blower. Turn to the left at "0"
to turn it OFF.
For Best Result
Start the rangehood several minutes before
For Best Result
Start the rangehood several minutes before cooking to develop proper
cooking to develop proper airflow. Allow the unit
airflow. Allow the unit to operate for several minutes after cooking is
to operate for several minutes after cooking is
complete to clear all smoke and odors from the kitchen.
complete to clear all smoke and odors from the
Cleaning
kitchen.
The stainless steel grease filters and grease rail should be cleaned
frequently in hot detergent solution or washed in the dishwasher.
Clean exterior surfaces with a commercially available stainless steel
cleaner. Abrasives and scouring agents can scratch stainless steel
finishes and should not be used to clean finished surfaces.
Cleaning
Grease rail and Grease Filter Installation / Removal
The stainless steel grease filters and grease rail
should be cleaned frequently in hot detergent
Remove the plastic from the filter, the knobs need to be installed
solution or washed in the dishwasher. Clean
onto the filter with 2 screws to each filter
exterior surfaces with a commercially available
Install the grease rail into the back of the hood, into the slots on the
stainless steel cleaner. Abrasives and scouring
inside floor of the rear of the hood. The Grease filters should be
agents can scratch stainless steel finishes and
installed before operating the rangehood. To install the filters, use the
two knobs (in FIGURE 28) to hold the filter and insert the filter into
should not be used to clean finished surfaces.
the front edge of the hood with the knobs facing out into the spring
loaded slot. Install the other end of the filter above the grease rail in
the back of the hood.
Grease rail and Grease Filter Installation /
Removal.
Remove the plastic from the filter, the knobs
need to be installed onto the filter with 2
screws to each filter.
9a
9a
3
9a
B
9a
2
lamp. Press and twist the lamp to remove. Then remove the lamp
and replace with a new lamp.
Install the grease rail into the back of the hood,
into the slots on the inside floor of the rear of the
hood. The Grease filters should be installed before
operating the rangehood. To install the filters, use
the two knobs to hold the filter and insert the filter
into the front edge of the hood with the knobs
facing out into the spring loaded slot. Install the
FIGURE 27
other end of the filter above the grease rail in the
back of the hood.
FIGURE 28
WIRING DIAGRAM
R11B41
A
B
LIGHT CONTROL
OFF / HALF LIGHT / ON
1
2
3
4
• Remove the snap-on lamp cover by levering it from
under the metal ring, supporting it with one hand.
• Replace the lamp with a new one of the same type,
making sure that you insert the two pins properly
into the housings on the lamp holder.
• Replace the snap-on lamp cover.
WIRING BOX
LINE IN
WHT
N
120Vac
BLK
L
60Hz ~
Y-G
a
This rangehood uses 45 watt PAR16
Halogen Lamps.
b
Gu10 self-ballasted led lamps
– listed in accordance with ul
1993/nmx-j-578/1-ance/csa
c22.2 No. 1993
ON/OFF MOTOR
SPEED CONTROL
Lighting unit
1
2
3
4
5
6
Y-G
BLU
3
2
1
3
2
1
6
5
4
6
5
4
Y-G
3
2
1
3
2
1
6
5
4
6
5
4
WIRING BOX FOR
9
8
7
9
8
7
REMOTE BLOWER
Y-G
1
2
3
1
2
3
4
5
6
4
5
6
7
8
9
7
8
9
M8 4V
M8 4V
REMOTE
120V ~
120V ~
BLOWER
BRW
BRW
a
b
Version 07/11 - Page 11
15
Publicité
Table des Matières
