Faber INCA PRO PLUS INPL3019SSNB-B Instructions D'installation page 10

INSTALLATION
BLOWER (1200 cfm)
INSTALLATION WITH IB1200 INTERNAL BLOWER (1200 cfm)
1. Install the Duct Plate B (Figure 7) which came
with the internal blower kit, on top of the rangehood
1. Install the Plate B (FIGURE 14) which came with the internal
blower kit, on top of the rangehood with the holes located closer to
with the holes located closer to the front. Use 9
the front. Use 9 screws supplied with the blower kit
screws supplied with the blower kit.
FIGURE 14 FIGURE 7
2. Remove the white plastic covering and Install the 4 side trim
pieces to the outside of the hood using (16) part 9b screws, see
FIGURE 14
the side rail installation in (FIGURE 15).
2. Remove the white plastic covering and Install
the 4 side trim pieces (4-5) to the outside of the
hood using (14) part 9c screws, see the side trim
installation in (Figure 8).
9c
FIGURE 15
3. Attach the blower bracket divider inside the hood, with the 2
screws into the top of the hood and 2 screws into the back, all
supplied with the blower kit (FIGURE 16)
5
FIGURE 15
4
FIGURE 8
3. Attach the blower bracket divider inside the
FIGURE 15
hood with the 2 screws into the top of the hood
and 2 screws into the back, all supplied with the
blower kit (Figure 9).
FIGURE 16
4. Install the 2 motor kits into the sides of the blower bracket using
the 4 screws supplied with the motor kit. (FIGURE 17)
5. Connect the wire (FIGURE 18) that comes with the motor kit
from the side of the two motors to the connection on the inside
of the light panel in the hood. The two - 9 hole ends of the wire
FIGURE 16
are installed in the two motors, the 6 hole end is connected to
the light panel (FIGURE 11 on the previous page)
FIGURE 9
10
WITH IB1200 INTERNAL
B
B
B
B
4
4. Install the 2 motor kits into the sides of the
blower bracket using the 4 screws supplied with
the motor kit (Figure 10).
FIGURE 17
FIGURE 10
FIGURE 17
5. Connect the wire cable D (which is located
inside of Kit
#; IB1200
box and connect the 9 hole end (B-C) to the two
motors (Figure 11).
FIGURE 18
B) 9 hole end
6. Install the 2 dampers on top of the hood. If you want one 10"
FIGURE 17
round duct to come out of the top of the hood, use the transition
piece (FIGURE 19) that comes with the motor kit and install with
FIGURE 18
four screws. If you want to use 2 seperate 6" round ducts, do not
use the transition. 6. Install the 2 dampers on top of the hood. If you want one 10"
round duct to come out of the top of the hood, use the transition
7. Attach the hood to the cabinet using (12) 9c. screws to the
piece (FIGURE 19) that comes with the motor kit and install with
cabinet. FIGURE 20
four screws. If you want to use 2 seperate 6" round ducts, do not
FIGURE 17
use the transition.
8. Follow steps 6 - 9 on the previous page to connect ducting,
wiring, and test the electrical connection.
7. Attach the hood to the cabinet using (12) 9c. screws to the
cabinet. FIGURE 20
FIGURE 18
8. Follow steps 6 - 9 on the previous page to connect ducting,
6. Install the 2 dampers on top of the hood. If you want one 10"
wiring, and test the electrical connection.
round duct to come out of the top of the hood, use the transition
piece (FIGURE 19) that comes with the motor kit and install with
four screws. If you want to use 2 seperate 6" round ducts, do not
use the transition. B) 9 hole end
7. Attach the hood to the cabinet using (12) 9c. screws to the
5
FIGURE 18
cabinet. FIGURE 20
FIGURE 19
6. Install the 2 dampers on top of the hood. If you want one 10"
FIGURE 11
8. Follow steps 6 - 9 on the previous page to connect ducting,
round duct to come out of the top of the hood, use the transition
wiring, and test the electrical connection.
piece (FIGURE 19) that comes with the motor kit and install with
four screws. If you want to use 2 seperate 6" round ducts, do not
6. Install the 2 dampers (A) on top of the hood
use the transition.
FIGURE 19
(which is located inside of Kit
7. Attach the hood to the cabinet using (12) 9c. screws to the
PRO Blower sku #; IB1200
cabinet. FIGURE 20
the 10" duct transition (E) (which is located inside
8. Follow steps 6 - 9 on the previous page to connect ducting,
Internal 1,200 cfm PRO Blower sku #;
of Kit
wiring, and test the electrical connection.
IB1200
) and install with four screws (Figure 12).
FIGURE 19
FIGURE 20
FIGURE 12
FIGURE 19
FIGURE 20
7. Follow step 4 on page 13 to connect ducting,
wiring, and test the electrical connection.
Internal 1,200 cfm PRO Blower sku
). Connect the 6 hole end (A) to the wire
C) 9 hole end
). Alternatively, install
Version 07/11 - Page 9
E
Version 07/11 - Page 9
C) 9 hole end
A) 6 hole end
D
A) 6 hole end
Internal 1,200 cfm