Güde GHS 510 P Traduction De La Notice Originale page 10

• WARNING! Use of accessories and adapters not
explicitly recommended in this user guide may result in
damage to persons and things.
• Do not incline from your position. Avoid abnormal
body posture! Make sure you are standing safely and
keep your balance.
The trimmer may be used only for the intended purpose.
Each deviation from the purpose is regarded as
unauthorized use. The manufacturer assumes no
responsibility for material and personal damage due to
unauthorized use and the same rests on the user.
Safety instructions specific for this device
Plug the trimmer only to a socket fitted with a
switch against stray current (FI)!
Protect all cables against excessive temperature, oil and
sharp edges.
Unplug the trimmer during repairs and maintenance
and if the trimmer is not used.
Work on electric devices may performed by a qualified
electrician only. Use genuine spare parts only.
Be aware of what you are doing. Approach your work
with sound mind.
Use the trimmer in suitable environment and avoid
exposure to moisture and wet.
Always provide good lighting during work.
In case of dangerous situation or technical failure turn
the trimmer off immediately and unplug from socket.
Only tools and accessories approved by the
manufacturer may be used. Use of unproved
components may result in accident.
Children and persons who lack experience and knowledge
for use of the trimmer or of which physical, sensory and
mental capabilities are limited may not use the trimmer
without supervision or guidance by a safety engineer.
Children must be under adult supervision to avoid
using the tool as a toy.
Do never touch the tool with wet hands.
Do not work in wet environment.
Do not overload your trimmer! Operate the trimmer within
specified working capacity.
Do never direct the blade strip to your body or other
persons or animals.
Hold the trimmer on the switch handle (fig. 1/6) with one
hand and on the guiding handle (fig. 1/4) with the other
hand.
Application according to intended use
This hedge trimmer is suitable exclusively for trimming of
hedges, bushes and ornamental shrubs while observing all
technical data and safety instructions.
Any other use contradicts to the intended use. Manufacturer
is not responsible for subsequent damage and injuries.
Please note the trimmer is intended for domestic use only.
Safety instructions for the first commissioning
Always pay attention to correct tightening of all bolt joints
and use genuine spare parts supplied only!
Branches of diameter over 14 mm must be first
cut by branch scissors in order to avoid damage to the
trimmer.
Assembly (fig. 2+3)
Hand protection:
Install the hand protection according to figure 2 with two
bolts supplied and make sure they are tight enough.
Do never use the trimmer without hand protection.
Cable tension reliever:
In order to avoid unintentional pulling of the connection
cable out of the switch/socket combination, make sure the
connection cable is attached correctly to the cable tension
reliever - see fig. 3.
Service (Fig. 1+4+5+6)
Remove the blade cover before use and when the
plug is extended (fig. 1/1).
Turning on:
Insert the plug to the mains supply socket.
The Güde hedge trimmer is fitted with two-hand safety
switch. The hedge trimmer operates only when the switch
(fig. 1/5) on the guiding handle (fig. 1/4) is switched by one
hand and the other hand switches the switch on the handle
(fig. 1/6).
Use:
Start trimming always as closest as possible to power
supply source in order to always have power supply behind
you.
Trapezoid trimming conforms to natural growing of plants
and allows the hedge to prosper optimally.
•
First trim the sides from below. Trim the upper side
either straight, roof-shaped or rounded as you like it.
• The safety blade strip has alternatively arranged
cutters rounded on their sides to reduce injury hazard.
Extra shock protection avoids unpleasant rebounds
from walls, fences etc.
• If the blade clogs, turn the trimmer off immediately,
disconnect from the power supply and then remove the
clogged piece.
• Attention: Metal things, e.g. mesh wires, plant supports
etc. may result in damage to the blade strip.
•
The best cutting performance is achieved if you trim
the hedge so that the blade form 15° angle with the
hedge. (fig. 4)
•
In order to achieve equal hedge height, we
recommend install a guiding cord along the hedge. Cut
any protruding branches. (fig. 5)
•
Trim the side areas of the hedge by rounded
movements from below. (fig. 6)
10