Installation Instructions - Truma Mover SE Mode D'emploi Et Instructions De Montage

Installation instructions

Read the installation instructions prior to starting work and
follow them carefully!
Intended use
The Mover SE is designed for use on single-axle caravans with
a gross weight of up to 1800 kg,
and the Mover TE is designed for use on dual-axle caravans
with a gross weight of up to 2250 kg.
The Mover SE/TE weighs approx. 33 kg.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma-Mover SE/TE has design approval, and a general
operating permit (ABE) has been issued for Germany. Accept-
ance by a vehicle expert is not required (except when installing
the flat frame kit). The ABE must be kept in the vehicle.
The Mover SE/TE complies with the vehicle engine interfer-
ence suppression directive 72/245/EEC with supplements
2004/104/EC and 2005/83/EC and bears type approval number:
e1 03 4473.
The Mover SE/TE complies with EMC directive 89/336/EEC.
The remote hand set and the receiver comply with the
requirements of the R&TTE directive 1995/5/EC.
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover is being installed.
Any modification to the unit, or the use of spare parts and
functionally-important accessories which are not original
Truma components, or failure to respect the installation and
operating instructions, will lead to the cancellation of the guar-
antee and to exclusion of claims for liability. in addition to this,
the operational approval for the device will be cancelled.
Tools and facilities required
To install the unit you will need:
13 mm, 17 mm socket wrench, ring spanner or open-jawed
spanner
Torque wrench (20 – 40 Nm)
Cable cutter/Crimping tool
Power drill/screwdrivers / 25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting.
Minimum installation dimensions
The equipment can only be fitted to caravans/trailers within the
following dimensions.
Caravan Floor
opt. 185
min. 30
max. 48
min. 60
max. 2400
all dimensions in mm
* with fully loaded vehicle
max. 1860
A distinction is made between L-profiled and U-profiled
chassis as shown in the illustration.
Caravan Floor
L-Profile
Measuring the chassis height
Frame height (Y) measured at distance of 106 mm (X) from the
outer edge of the tyre at height of hub/middle of tyre.
Determining the installation type
1. Standard installation
Standard installation is used with a U-profile or L-profile chas-
sis and a frame height (Y) of approx. 185 mm. No special
accessories are required.
2. Installation with chassis with U-profile or L-profile and
frame height of between 140 and 185 mm
With a chassis with a frame height (Y) of 140 mm to 185 mm,
1, 2 or 3 spacer plate sets and the screw set are needed to
compensate for the height.
3. Installation with chassis with U-profiles or L-profiles
with frame height of less than 140 mm
With a chassis with a frame height (Y) of less than 140 mm a
low chassis kit must be fitted to compensate for the height.
In Germany, the low chassis kit installation must be
accepted by a vehicle expert.
4. The AL-KO Vario III/AV installation kit must be used
with the AL-KO Vario III/AV chassis with a frame thickness of
less than 2.8 mm.
5. Installation with Eriba Touring chassis
The Eriba Touring mounting set is needed for the Eriba Touring
chassis.
Special accessory installation
1. Set of screws
for height compensation with
spacer plates, max. 45 mm,
eight DIN 933 screws
M10 x 95 8.8, galvanized,
Part no. 60010-70000.
2. Spacer plate kit
(two 15 mm spacer plates)
for height compensation
max. 45 mm (3 plates) at each
side (e.g. installed behind axle)
Part no. 60010-66000.
U-Profile
17