Yamaha DSP-AZ2 Mode D'emploi page 67

Amplificateur audio-vidéo
Masquer les pouces Voir aussi pour DSP-AZ2:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 84
I Setting by "msec"
Control range:
0 to 5.0 ms (for center), 0 to 30.0 ms
(for rear center)
Initial settings:
0 ms (for center), 3.0 ms (for rear
center)
12 SP DELAY
≥ U N I T ... ... ... ... ... ... ... ... m s e c
C E N T E R ... ... ... ... ... 0 . 0 m s
R E A R C T ... ... ... ... 3 . 0 m s
I Setting by "meters"
Control range:
0.15 to 30.00 m (for main L/R,
center, rear L/R, rear center)
Initial settings:
3.00 m (for main L/R, center, rear L/
R), 2.10 m (for rear center)
12 SP DELAY
≥ U N I T ... ... ... ... ... ... m e t e r s
M A I N L / R ... ... ... 3 . 0 0 m
C E N T E R ... ... ... ... ... 3 . 0 0 m
R E A R L / R ... ... ... 3 . 0 0 m
R E A R C T ... ... ... ... 2 . 1 0 m
I Setting by "feet"
Control range:
0.5 to 100 ft (for main L/R, center,
rear L/R, rear center)
Initial settings:
10.0 ft (for main L/R, center, rear L/
R), 7.0 ft (for rear center)
12 SP DELAY
≥ U N I T ... ... ... ... ... ... ... ... f e e t
M A I N L / R ... ... 1 0 . 0 f t
C E N T E R ... ... ... ... 1 0 . 0 f t
R E A R L / R ... ... 1 0 . 0 f t
R E A R C T ... ... ... ... 7 . 0 f t
Note
• No delay will be set if the same distance is set for the main L/R
and center, or the rear L/R and rear center with "meters" or
"feet" selected.
13 DISPLAY SET
13 DISPLAY SET
≥ D I M M E R ... ... ... ... ... ... ... ... ... 0
O S D S H I F T ... ... ... ... ... ... 0
G R A Y B A C K ... ... ... A U T O
V C O N V . ... ... ... ... ... ... O F F
I DIMMER
You can adjust the brightness of the front panel display.
Control range: –4 to 0
Initial setting: 0
I OSD SHIFT (OSD off-set position)
This setting is used to adjust the vertical position of the
OSD.
Control range: +5 (downward) to –5 (upward)
Initial setting: 0
Press + to lower the position of the OSD.
Press – to raise the position of the OSD.
I GRAY BACK
Selecting AUTO for the on-screen display setting displays
a gray background when there's no video signal input.
Nothing is displayed on the screen including the on-
screen display if OFF is selected.
Choices: AUTO, OFF
Initial setting: AUTO
Note
• If "GRAY BACK" is set to OFF, no information will be
displayed on the screen when video signals are not being input.
I V CONV. (Video conversion)
(Europe and U.K. models only)
Use this feature to turn on/off the function to convert
composite signals to S-video signals to output through the
S-video jack when no S-video signals are input.
Choices: ON, OFF
Initial setting: OFF
OFF
Select this not to convert composite signals to S-video
signals.
ON
Select this to convert composite signals to S-video
signals.
SET MENU
65

Publicité

Table des Matières
loading

Table des Matières