Changing Parameter Settings; Resetting A Parameter To The Factory-Set Value - Yamaha DSP-AZ2 Mode D'emploi

SOUND FIELD PROGRAM PARAMETER EDITING

Changing Parameter Settings

You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
3
10KEY DSP HALL 1
ROCK
CONCERT
MOVIE
EX/ES THEATER 1
CHP/INDEX
A/B/C/D/E
TV INPUT
TV VOL
TV MUTE
4
2
ON SCREEN LEVEL
SLEEP TEST
5
1
Set PARAMETER/SET
MENU to PARAMETER.
2
Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3
Select a DSP program you want to adjust.
10KEY DSP HALL 1
1
ROCK
CONCERT
5
MOVIE
THEATER 1
9
Program No.
P05 ROCK CONCERT
T h e R o x y T h e a t r e
D S P L E V E L ... ... ... ... 0 d B
Cursor
≥ I N I T . D L Y ... ... ... ... 1 5 m s
R O O M S I Z E ... ... ... ... 1 . 0
L I V E N E S S ... ... ... ... ... ... ... 5
R E V . T I M E ... ... ... ... 1 . 6 s
Parameters
Example of the parameter setting display
70
HALL 2 CHURCH JAZZ CLUB
1 2 3 4
ENTER- MUSIC TV
TAINMENT VIDEO THEATER
5 6 7 8
MOVIE /DTS
THEATER 2 SUR. SELECT
9 10 11 12
0 + 10 + 100
PRESET
MUTE
CH VOLUME
STEREO
DISC EFFECT
1
PARAMETER
SET MENU
PARAMETER
SET MENU
ON SCREEN
HALL 2 CHURCH JAZZ CLUB
2 3 4
ENTER- MUSIC TV
TAINMENT VIDEO THEATER
6 7 8
MOVIE /DTS
THEATER 2 SUR. SELECT
10 11 12
+ +
0 10 100
Program name
Parameter valves
4
Press k / n to select the
parameter.
5
Press –/+ to change the
parameter value.
When you set the parameter to
a value other than the factory-
set value, an asterisk mark (*)
appears by the parameter name
on the video monitor.
6
Repeat steps 3 to 5 above as necessary to
change other program parameters.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press k / n.
• You cannot change parameter values when "14 MEMORY
GUARD" on the SET MENU is set to ON. If you want to
change the parameter values, set "14 MEMORY GUARD" to
OFF (see page 66).
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
I To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold –/+ until the value temporarily stops at the factory-
set value. The asterisk mark (*) by the parameter name
disappears on the video monitor.
I To reset all of the parameters to
the factory-set values
Use "9 PARAM. INI" on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 63).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.