Publicité
• Ensure a clean working environment.
• Only use perfect tools that are free of cracks and other defects (e.g. deformations).
• Remove tool keys and other adjustment tools before switching on the machine.
• Keep the area around the machine free of obstacles (e.g. dust, chips, cut parts, etc.).
• Check the strength of the machine connections before each use.
• Never leave the running machine unattended. Switch off the machine before leaving the
working area and secure it against unintentional or unauthorised recommissioning.
• The machine may only be operated, serviced or repaired by persons who are familiar with it and
who have been informed of the hazards arising from this work.
• Ensure that unauthorised persons maintain a safe distance from the machine and keep
children away from the machine.
• Wear close-fitting protective clothing and suitable protective equipment (eye protection, dust
mask, ear protection; gloves only when handling tools).
• When working on the machine, never wear loose jewellery, loose clothing, ties or long, open
hair.
• Hide long hair under hair protection.
• Always work with care and the necessary caution and never use excessive force.
• Do not overload the machine!
• Do not work on the machine if it is tired, not concentrated or under the influence of medication,
alcohol or drugs!
• Do not use the machine in areas where vapours from paints, solvents or flammable liquids
represent a potential danger (danger of fire or explosion!).
• Do not smoke in the immediate vicinity of the machine (fire hazard)!
• Shut down the machine and disconnect it from the power supply before carrying out any
adjustment, conversion, cleaning, maintenance or repair work. Before starting any work on the
machine, wait until all tools or machine parts have come to a complete standstill and secure the
machine against unintentional restarting.
12.4
Electrical safety
• Improper use of extension cords may cause inefficient operation of the machine, resulting in
overheating. Make sure that the extension cord is not longer than 10 m and its cross-section is
not less than 2.5 mm² to allow sufficient current flow to the motor.
• Avoid using free and insufficiently insulated connections. Connections must be made with
appropriate material suitable for outdoor use.
• A damaged or tangled cable increases the risk of electric shock. Handle the cable with care.
Never use the cable to carry, pull or disconnect the power tool. Keep the cable away from heat,
oil, sharp edges or moving parts.
• Proper plugs and sockets reduce the risk of electric shock.
• Water entry into machine increases the risk of electric shock. Do not expose machine to rain or
moisture.
• The machine may only be used in humid environments if the power source is protected by a
residual current circuit breaker.
• Do not use the power tool if it cannot be turned on and off with the ON-OFF-switch.
12.5
Special safety instructions for this machine
• When using milling tools with a diameter of ≥ 16 mm and circular saw blades, these must
comply with EN 847-1:2013 and EN 847-2:2013; tool carriers must comply with EN 847-3:2013.
• Excessive noise can cause hearing damage and temporary or permanent hearing loss. Wear
hearing protection certified to health and safety regulations to limit noise exposure.
• Replace cracked and deformed saw blades immediately, they cannot be repaired.
• Use saw blades that are clean and sharpened, they are less prone to failure and are easier to
guide.
• Never attempt to cut logs that contain nails, wire or debris. Branches must be cut flush with the
trunk.
• Always maintain a secure standing position and balance. Never stand on the machine. Serious
injury can occur if the machine tips over or if the cutting tool is accidentally touched. Do not
keep objects above or near the machine that someone could stand on to reach the machine.
• Do not attempt to load or unload logs until the machine has stopped.
• Do not remove residual pieces or other parts of the workpiece from the cutting area while the
machine is running, unless you use a push stick.
• Keep your hands away from all moving parts.
• Do not grasp around the saw blade with both hands while the machine is running.
• Avoid awkward cutting operations and hand positions where a sudden slippage could cause
your hand to get caught at the saw blade.
ZIPPER MASCHINEN GmbH
ZI-WP500TN
www.Zipper-Maschinen.at
SAFETY
23
Publicité
