Publicité
Program
number display by one.
Keeping
the button pressed increases the tune number
continuously.
* — Computomatic Program Search (page 8)
Computomatic Direct Selection (page 8)
*** Programmed music search (page 7)
**
@ MEMO/CHECK Button
Press to store tune numbers set using the
PGM
button.
After
storing, pressing the
MEMO/CHECK
button
lets you
check
stored tune numbers. Each time it is pressed,
the tune numbers are displayed in the order
in which they are stored; keeping the button
pressed,
the display
shows
all the tune
numbers in sequence.
@ INTRO CHECK Button
When
this is pressed, the deck plays the
first 15 seconds (approx.) of each tune and
fast-winds the tape between these sections.
Auto-reverse functions by means of the
newly developed Super A.R.H.S. (Ac-
culign Rotating Head System)
and a
special |.R. (infrared) Combination Tape
Sensor. This head rotating system allows
the record/playback head to turn the
head at the moment
the direction of
tape movement is reversed to the reverse
play or record
mode.
Therefore,
one
doesn't have to be concerned about level
difference between sides A and B, except
the effect caused by the tape, etc. The
I.R. Combination
Tape Sensor sends a
signal when detecting the leader tape
portions during the play or record mode
to the tape transport control. This signal
activates this control so that the tape
will
immediately
be
changed
to the
reverse or forward mode. In the case of a
Auto-Reverse Mechanism
tape without a leader tape portion, the
direction of the tape will automatically
be reversed when the tape reaches the
end.
Notes:
eThe
auto-reverse
function
cannot be
activated during the first 15 seconds of
a tape run, even when leader tape is
detected.
eDuring
a programmed
music search,
leader tape can not cause the tape run
to switch to the reverse mode.
elf the tape is flawed or the head unit is
exposed to strong light, the tape direc-
tion may be reversed before the end
of the tape even when the AUTO
REVERSE switch is set in the'——' or
'cD' position.
Tape Travel Depending on Setting of AUTO REVERSE Switch
Tape Travel Mode
when
the
tape
reaches
the
end,
the play or record mode will be re-
leased.
(@® During
forward
play or record,
when
the
tape
reaches
the
end,
the direction of tape movement will
reverse to the reverse play or record
mode.
Reverse
play or record will
continue to the end at which time
the play or record
mode will be
released.
(@ During
reverse play or record,
when
the
tape
reaches
the
end,
the play or record mode will be re-
leased.
Beginning
During either forward or reverse play
operation, when the tape reaches the
end,
the direction
of tape
move-
ment will be reversed and play will
continue
in the opposite direction.
This operation will be repeated up to
5 times unless the STOP button is
pressed.
eFor continuous playback/recording
using the CONT REC/PLAY posi-
tion, refer to page 6.
Setting
Beginning
Side B
End
------------ |
ea nae
Start
Stop
Stop
Start
ee
ee
eee
End
Side A
Beginning
L
Side B
Beginning
End
=>)
Side A
Play mode
Peer
Side B
Beginning
End
CG
End
Side A
Record mode: Same as —
a5=
(See page 6.)
@® BLANK SCAN Button
With this button
engaged (the indicator
lights), when a blank portion of more than
10 seconds is detected, the tape skips to the
beginning of the next tune from which
point playback resumes. When it is pressed
again, this function is cleared (the indicator
goes off). (See page 8.)
@ SYNC REV Button
Using this
button reverses the tapes in both
decks simultaneously during dubbing. (See
"Synchro Reverse dubbing" on page 10.)
@® HIGH Speed DUB START Button
Press when quick dubbing (2 times faster) is
required. (See page 9.)
® NORMal Speed DUB START
Button
Press
for
normal
speed
dubbing.
(See
page 9.)
@ REC MUTE Button
Press this button during recording to leave
about 4 seconds of blank space on a tape.
The deck will enter the record pause mode.
Press the PAUSE button to start recording
again.
(See "Record
Muting
Operation"
on page 6.)
® Display Window
@ Counter Display:
Normally this shows the tape counter. When
the CPS, CDS, PGM or CD CHECK mode is
activated, the corresponding display appears.
a) Tape counter mode
'i
1
1
7
=
!
—_
(~~ [~~
b) CPS mode
—_
a)
--
c) CDS mode
d) PGM mode
e) CD CHECK mode
Auto Reverse Indicator:
Shows the auto reverse mode according to
the setting of the AUTO REVERSE switch.
© SYNC, REV Indicator:
Lights when the SYNC REVERSE
mode is
activated.
©B. SCAN Indicator:
Lights when
the BLANK
SCAN
mode is
activated.
© PEAK LEVEL METER display
with Tape Type Indicators:
When recording, set the recording level so
that the peak value reaches the tape type
indicator
corresponding
to the tape used
(NORM, CrO, or METAL).
Publicité
