Publicité
2. Disconnect the product from the compressed air
source after work.
Note:
First disconnect the hose from the compressed air source
(compressor) and only then remove the supply hose from
the product. In this way you avoid whirling of the supply
hose.
10.2
Regulate oscillating power
• The speed controller (6) can be used to vary the air
flow and thus the oscillating power during operation.
• The ideal oscillation power depends on the material
and can be determined by a practical trial.
• Check the speed and vibration level after each use.
Set the correct working pressure using the pressure re-
ducer. Use the product with a working pressure of max.
6.3 bar.
11 Working instructions
The most important thing when sanding is to use sanding
sheets with progressively finer grits. If the grit is too
coarse, the surface will not be smooth, but even rougher.
If the grit is too fine, you will hardly achieve any results.
The removal rate is determined by the speed and grit of
the sanding sheet. Different sanding sheets should be
used depending on the material to be machined and the
desired removal of the surface.
• The dusts and vapours generated by the use of sand-
ing sheet sanders or polishers can cause damage to
health (such as cancer, birth defects, asthma and/or
dermatitis); it is essential to carry out a risk assess-
ment in relation to these hazards and to implement
appropriate control mechanisms.
ATTENTION
Always disconnect the product from the compressed air
source before attaching or detaching the sanding sheet.
Material
Paint/varnish:
Sanding
Repairing scratches 120
Removing rust spots 40
Wood:
Softwood
Hardwood
Veneers
Metal:
Aluminium
Steel
11.1
ATTENTION
–
–
–
Note:
The removal rate and the sanding pattern are essentially
determined by the choice of sanding sheet and the con-
tact pressure. Only flawless sanding sheets deliver good
sanding performance.
1. Switch on the compressed air source and let it run un-
2. Set the optimal working pressure using the pressure
3. Switch the product on.
4. Allow the product to run at the desired speed and reg-
5. Guide the product parallel to the workpiece surface.
6. Move the product in parallel and in a circular or alter-
Grain
7. Ensure that the contact pressure is even. Excessively
180
8. Do not use a sanding sheet with which metal has
60-80
60
12 Maintenance and cleaning
240
80
60
Danger of injury!
Always disconnect the product from the compressed air
supply before carrying out maintenance work.
Note:
The following points must be observed to ensure that the
product functions perfectly and has a long service life:
www.scheppach.com
Sanding
Sanding produces sanding dust. Always wear pro-
tective gloves and suitable respiratory protection
and clean the sanding sheet and workpiece at regu-
lar intervals using a vacuum cleaner or compressed
air.
Depending on the size and type of workpiece, ap-
propriate safety precautions must be taken. Use
suitable clamping devices to prevent the workpiece
from slipping.
In the event of an interruption in the compressed air
supply, release the trigger immediately.
til the maximum accumulator pressure has been
reached and the compressor switches off.
reducer on the compressed air source. Ensure that
the maximum working pressure is not exceeded. Ex-
cessive working pressure does not improve perfor-
mance, but only increases compressed air consump-
tion and accelerates wear of the product. Therefore,
always adhere to the technical specifications.
ulate it as required.
nating longitudinal and transverse direction. Use the
housing as a handle to guide the product in the de-
sired direction.
increasing the contact pressure does not lead to a
higher sanding rate, but to greater wear on the sand-
ing sheets.
been machined for other materials.
WARNING
• Any work not described in this operating manual must
be performed by an authorised specialist workshop
only.
• For safety reasons, replace worn or damaged parts.
• Sufficient and continuous oil lubrication is of crucial
importance for optimum function.
GB | 19
Publicité
