Publicité
Drilling into metal
• Use metal drill bits (HSS). For best results, cool the
drill with cooling lubricant* (cutting oil). Metal drills
can also be used for drilling into plastic. First pre-
drill with a Ø 3mm drill bit and approach the desired
drill diameter.
Drilling into wood
• Use a wood drill with a centre point.
Depth holes: Use an "auger"*.
Large drill diameter: Use a Forstner drill*.
Small screws* in soft wood can also be screwed in
directly without predrilling.
Drilling into bricks
• Used a carbide-tipped masonry drill (max. Recom-
mended drilling diameter Ø 13 mm).
12 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the
battery removed. There is a danger of inju-
ry! Let the product cool down before all
maintenance and cleaning tasks. Elements
of the engine are hot. There is a danger of
injury and burning!
The product can start unexpectedly and cause inju-
ries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
12.1
Cleaning
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth* or blow it off with
compressed air* at low pressure. We recommend
that you clean the product directly after every use.
2. Ventilation openings must always be free.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interi-
or.
4. Wipe any dirt off the lens with a dry cloth. Be careful
to avoid scratching the LED lamp as this can se-
verely reduce the light intensity.
12.2
Maintenance
The product is maintenance-free.
13 Storage
Preparation for storage
1. Remove the battery from the product before pro-
longed storage (e.g. winter storage).
2. Clean and check the product for damage.
30 | GB
3. Store the battery in a partially charged state.
4. When stored, check the battery charge level every
three months.
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
14 Repair & ordering spare parts
With this product, it is necessary to note that the follow-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consumables.
ATTENTION
According to the German Product Liability Act, no lia-
bility is accepted for damage caused by improper re-
pairs or by not using original spare parts.
Such work should be performed by a customer ser-
vice centre or an authorised specialists. The same
applies to accessory parts.
Spare parts and accessories can be obtained from our
Service Centre. To do this, scan the QR code on the
front page.
14.1
Ordering spare parts
Please provide the following information when ordering
spare parts:
• Model designation
• Item number
• Type plate data
Spare parts / accessories
Battery pack SBP2.0 - Article no.:
Battery pack SBP4.0 - Article no.:
Battery charger SBC2.4A - Article no.:
Battery charger SBC4.5A - Article no.:
Battery charger SDBC2.4A - Article no.:
Battery charger SDBC4.5A - Article no.:
StarterKit SBSK2.0 - Article no.:
StarterKit SBSK4.0 - Article no.:
15 Disposal and recycling
Notes for packaging
www.scheppach.com
7909201708
7909201709
7909201710
7909201711
7909201712
7909201713
7909201720
7909201721
The packaging materials are re-
cyclable. Please dispose of pack-
aging
in
an
environmentally
friendly manner.
Publicité
