Publicité
Les langues disponibles
Les langues disponibles
9.4
Charge battery
WARNING
Observe the following information to re-
duce hazards:
–
Never leave batteries to charge unsupervised!
–
Remove rechargeable batteries from the charger
after charging.
–
Do not over-charge batteries! Observe the maxi-
mum charging times. These charging times only
apply to discharged batteries. Inserting a charged
or partially charged battery multiple times leads to
overloading and cell damage. Do not leave batter-
ies in the battery charger for multiple days.
–
Never use or charge batteries if you suspect that
they were last charged more than 12 months ago.
The probability is high that the battery is already
dangerously damaged (deep discharge).
Charge the battery at an ambient temperature of 4 °C
to 40°C.
1. Push the battery (5) into the battery mount (6) as far
as it will go.
2. Plug the mains plug into the socket.
As soon as the charging process starts, the green
LED (14) flashes.
3. LED (14) lights up green when charging is com-
plete. The battery (5) is ready for use.
ATTENTION
–
If the red LED flashes, the battery has overheated
and cannot be charged.
–
IF the red and green LEDs flash, the battery is de-
fective.
4. Pull the battery (5) out of the battery holder (6).
5. Wait at least 15 min until a new charging process.
Therefore, pull the mains plug out of the outlet.
9.5
Inserting/removing the tool
attachment
WARNING
Tool attachments may be sharp and become hot
during use. Always wear protective gloves when han-
dling the tool attachments.
CAUTION
Keep your hands away from the tool attachment
when the product is in operation.
1. Turn the quick-release chuck (2) anti-clockwise until
the chuck opening (1) is large enough to insert the
tool attachment.
28 | GB
2. Insert the tool attachment into the quick-release
chuck (2) as far as possible.
3. Turn the quick-release chuck (2) clockwise to clamp
the tool attachment tight.
4. To remove the tool attachment again, untwist the
quick-release chuck (2) and remove the tool attach-
ment.
9.6
Test run
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal nois-
es are heard.
1. Before operation, check whether the tool attach-
ment is properly attached, i.e. centred in the quick-
release chuck (2).
2. Screw bits are marked with their dimensions and
shape. If you are unsure, always try out first wheth-
er the bit sits in the screw head without play.
9.7
Gear selection
1. Push the gear selector switch (4) to 1
sponding to a low or high speed selection.
Gear 1 :
Suitable for:
Rotational speed:
Torque:
Gear 2 :
Suitable for:
Rotational speed:
Torque:
9.8
Set direction of rotation
ATTENTION
The direction of rotation switch may only be actuated
when idle.
With the direction of rotation switch, you can select the
direction of rotation of the product (clockwise or anti-
clockwise) and secure the product from being switched
on unintentionally. The arrow on the direction of rotation
switch indicates the working direction.
1. Wait until the product has come to a standstill.
2. Push the direction of rotation switch (10) to the de-
sired position:
– Clockwise rotation: For drilling and screwing
in screws. Press the direction of rotation switch
to the right.
– Anti-clockwise rotation: To undo screws.
Press the direction of rotation switch to the left.
www.scheppach.com
or 2 corre-
0 – 400 rpm
Screwing work
Low
High
0 – 1550 rpm
Drilling work
High
Low
Publicité
