Publicité
1
Introduction
Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer
We hope your new product brings you much enjoyment
and success.
Note:
In accordance with the applicable product liability laws,
the manufacturer of this product assumes no liability for
damage to the product or caused by the product arising
from:
• Improper handling
• Non-compliance with the operating manual
• Repairs carried out by third parties, unauthorised
specialists
• Installing and replacing non-original spare parts
• Improper use
• Failures of the electrical system in the event of the
electrical regulations not being observed.
Note:
The operating manual is part of this product.
It includes important instructions for the safe, proper
and economic operation of the product, for avoiding
danger, for minimising repair costs and downtimes and
for increasing the reliability and extending the service
life of the product. In addition to the safety instructions
in this operating manual, you must also observe the
regulations applicable to the operation of the product in
your country.
Familiarise yourself with all operating and safety in-
structions before using the product. Only operate the
product as described and for the specified areas of ap-
plication. Keep the operating manual in a good place
and hand over all documents when passing the product
on to third parties.
2
Product description (Fig. 1-4)
1.
Chuck opening
2.
Quick-release chuck
3.
Torque adjusting ring
4.
Gear selector switch
5.
Battery
6.
Battery mount
7.
Release button (battery)
8.
LED work lamp
9.
On/off switch
10.
Rotational direction switch
11.
Belt clip
12.
Screw
13.
Battery charger
14.
LED strips (battery charger)
15.
Wall bracket
16.
Bits
22 | GB
17.
Bit holder
18.
Metal drill
19.
Wood drill
20.
Sockets
21.
Measuring tape (5m)
22.
Countersink
23.
Center punch
24.
Cutter knife
25.
Mine
26.
Carpenter's pencil
27.
Button for battery charge status indicator
28.
Charge status indicator
3
Scope of delivery (Fig. 1)
Item Quantity Designation
5.
1 x
11.
1 x
12.
1 x
13.
1 x
16.
40 x
17.
1 x
18.
14 x
19.
5 x
20.
8 x
21.
1 x
22.
1 x
23.
1 x
24.
1 x
25.
1 x
26.
1 x
1 x
1 x
4
Proper use
The product is intended for screwing in and unscrewing
screws, as well as for drilling into wood, metal and plas-
tic.
The product may only be used in the intended manner.
Any use beyond this is improper. The user/operator, not
the manufacturer, is responsible for damages or injuries
of any type resulting from this.
An element of the intended use is also the observance
of the safety instructions, as well as the assembly in-
structions and operating information in the operating
manual.
Persons who operate and maintain the product must be
familiar with the manual and must be informed about
potential dangers.
The liability of the manufacturer and resulting damages
are excluded in the event of modifications of the prod-
uct.
The product may only be operated with original parts
and original accessories from the manufacturer.
The safety, operating and maintenance specifications
of the manufacturer, as well as the dimensions speci-
fied in the technical data, must be observed.
www.scheppach.com
Battery 20V 2Ah
(item no. 7909201708)
Belt clip
Screw
Battery charger 20V 2.4 A
(item no. 7909201710)
Bits
Bit holder
Metal drill
Wood drill
Sockets
Measuring tape (5m)
Countersink
Center punch
Cutter knife
Mine
Carpenter's pencil
Cordless drill
Operating manual
Publicité
