More Information; Troubleshooting - Rotel RSX-1058 Manuel D'utilisation

RSX-1058 Surround Sound Receiver
To change the FRONT REDIRECT set-
ting: Place the highlight on the FRONT RE-
DIRECT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to FRONT SP (for powering front speakers),
CB SP (for powering center back speakers),
ZONE 2, ZONE 3 or ZONE 4 (for power-
ing speakers in one of the Zones 2, 3 or 4).
If you redirect the internal amplifiers, then
you will need a separate stereo amplifier to
drive your front speakers.
NOTE: Changing the default TUNER SETTING
or REDIRECT SETTING can only be done at the
same time as restoring the FACTORY DEFAULT
settings. Therefore, we recommend selecting
your default TUNER and REDIRECT settings
and resetting to the FACTORY DEFAULT set-
tings as the first step in configuring the unit,
before you change or memorize any other
configuration settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the set-
ting to YES. Press the ENTER button to pro-
ceed with resetting the FACTORY DEFAULT
settings with re-confirmation screen. The unit
will power off (to Standby Mode) and then
on, with the factory settings restored. To re-
turn to the MAIN menu without resetting the
FACTORY DEFAULT settings, change the entry
to NO and press the ENTER button.
NOTE: Resetting to factory default settings will
erase all stored settings including delay settings,
speaker settings, balance settings, input settings
and more. You will lose ALL system configura-
tion settings. Be certain that you wish to do so
before resetting the factory defaults.
To memorize USER DEFAULT settings:
Many of the current configuration settings can
be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.
To save the current settings as a USER DE-
FAULT, place the highlight on the SET USER
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the set-
ting to YES.
You will then be asked to enter a PASSWORD.
If you have not previously entered a pass-
word, use the universal password '8888'.
Use the +/– buttons to enter each digit and
press ENTER to confirm.
To change your password, use the +/– buttons
to highlight the line SET NEW PASSWORD.
You may then enter and confirm your new
password in the same way, before returning
to the DEFAULT SETUP menu.
Press the ENTER button to store the new USER
DEFAULT settings. To return to the MAIN
menu without saving any changes, change
all entries on the screen to NO and press the
ENTER button.
NOTE: If there is insufficient memory to store a
USER DEFAULT configuration file, the SET USER
DEFAULT option will not be available.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT configuration file, you can activate
those settings at any time by placing the
highlight on the USER DEFAULT line using the
UP/DOWN buttons. Use the +/– buttons to
change the setting to YES. Press the ENTER
button to proceed with activating the USER
DEFAULT settings. To return to the MAIN
menu without activating the USER DEFAULT
settings, change the entry to NO and press
the ENTER button.
46

MORE INFORMATION

Troubleshooting

The unit does not turn on.
• Make sure the power cord is plugged into
the rear panel and a live AC outlet.
• Make sure the rear panel POWER switch
is in the ON position.
No sound from any input.
• Make sure that MUTING is off and VOL-
UME is turned up.
• Make sure that preamp outputs are con-
nected to a power amplifier and that the
amplifier is turned on.
• Make sure source inputs are connected
and configured correctly.
• Check that the setting for HDMI AUDIO
in the VIDEO/HDMI on-screen menu is
AMP MODE.
No sound from digital sources.
• Make sure that digital input connector is
assigned to the proper source input and
that the source input is configured to use
the digital input rather than an analog
input.
• Check the configuration of the DVD player
to ensure that the bitstream and/or DTS
digital output is activated.
No sound from some speakers.
• Check all power amp and speaker con-
nections.
• Check Speaker Configuration settings in
the Setup menus.
No video output on TV monitor.
• Make sure that the TV monitor is connected
properly and check the input assignments.
S-Video and Composite Video TV moni-
tors can only be used with interlaced SD
sources. HDMI and Component TV moni-
tors can be used with Standard Definition
(SD) and High Definition (HD) sources. An
HDMI 1080p source can only be sent to
a 1080p-compliant TV monitor.