Video 1-3 S-Video Inputs; Video 1-2 S-Video Outputs; Tv Monitor Outputs - Rotel RSX-1058 Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

RSX-1058 Surround Sound Receiver
TV monitor. S-Video signals cannot be con-
verted to Composite outputs. For maximum
convenience, connect the RSX-1058 to the
TV monitor with Component Video or HDMI
Video connections.
NOTE: When you have changed the output
resolution in the VIDEO/HDMI menu during
operation, restart by switching power OFF and
ON again, to stabilize the picture image in the
new resolution setup.
Many digital HDTV monitors adjust scan
rates and other video parameters depend-
ing on the type of input connection. You may
wish to make multiple connections between
the RSX-1058 and the TV monitor, switch-
ing inputs on the TV to take advantage of
these features.
NOTE: Do not connect HDMI and Compo-
nent Video outputs to a monitor simultane-
ously, as the two video image signals may
affect each other.
VIDEO 1–3
Composite Video Inputs
Three inputs accepts standard Composite
video signals from source components using
standard 75 ohm RCA video cables.
VIDEO 1–2
Composite Video Outputs
Two RCA jacks, labeled COMPOSITE OUT
1 & 2, provide connections for sending Com-
posite video signals for recording on a VCR
or other recording device. These connections
correspond to the VIDEO IN 1–3 connec-
tions. Make sure that you are consistent. If
you hook up a particular VCR to the VIDEO
1 inputs, hook up the VIDEO 1 output to the
same VCR.
Video Input/Output formats
�����������������������
����������������������������������������������������������������������������������������������������������������������������������
���������������
������������������� ���������������������������������������������������������������
����������������������������������� ��
��������������
������������������������������
�������������������������������������������
���������������������������������
���������������������������������������������
��������������������������������������������
�����������������������������������������������
�����������������������������������
���������������������������
������������������������������������
������������������������������������
NOTE: The RSX-1058 cannot convert S-Video
or Component Video to Composite Video. There-
fore, only signals from the Composite Video
inputs are available at these outputs.
VIDEO 1–3 S-Video Inputs
Three inputs, labeled S-VIDEO IN 1–3 accept
S-Video signals from source components.
VIDEO 1–2 S-Video Outputs
Two S-VIDEO jacks, labeled S-VIDEO OUT 1
& 2, provide connections for sending S-Vid-
eo signals for recording on a VCR or other
recording device.
These connections correspond to the VIDEO
IN 1–3 connections. Make sure that you are
consistent. If you hook up a particular VCR
to the VIDEO 1 inputs, hook up the VIDEO
1 output to the same VCR.
NOTE: The RSX-1058 cannot convert Com-
posite video or Component Video signals to
S-Video. Only signals received at the S-Video
inputs are available at these outputs.
VIDEO 1–3
Component Video Inputs
Component Video connections split the vid-
eo into three signals – luminance (Y) and
chrominance (P
delivery of a reference quality picture with
high definition signals. Component Video
connections should be used for progressive
scan DVD players and high-definition televi-
sion receivers. Each of these signals is car-
ried by a separate 75 ohm video cable with
RCA connectors.
Three sets of inputs, labeled COMPONENT
VIDEO IN 1–3 accept Component video sig-
nals from source components.
������������������������������������������
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
�����������������������������������������������
18
and P
) signals, allowing
B
R
NOTE: When using a progressive scan or
1080i HDTV video signal from the Component
Video inputs, the TV monitor cannot display
the video signal and the OSD menus at the
same time. When the main OSD setup menus
are displayed, the progressive video signal is
interrupted and restored when the OSD menus
are cancelled. The temporary OSD informa-
tion displays (such as volume setting, etc.) are
not displayed.
VIDEO 1–4
HDMI Inputs
HDMI inputs provide various digital video con-
nections for use with components that have
either HDMI outputs or DVI-D outputs (with
an appropriate DVI-HDMI adapter). HDMI
connections carry video signals in all formats
including progressive scan up to 1080p. The
implementation of HDMI supports audio sig-
nals, or a separate audio connection from
an HDMI component.
Four inputs, labeled HDMI VIDEO IN 1–4 ac-
cept signals from source components.
NOTE: When using HDMI connections, the TV
monitor can display the OSD menus and can
also display video from Composite, S-Video, or
Component Video sources, as the RSX-1058 is
capable of upscaling these signals.

TV Monitor Outputs

The TV MONITOR outputs of the RSX-1058
send the video signal to your TV monitor.
Four types of video output connections are
provided – RCA Composite video, S-Video,
Component Video, and HDMI digital.
The Composite Video output sends all interlace
video inputs to the TV monitor; the S-Video
output also sends all interlace video inputs to
the TV. The HDMI output sends all format video
inputs to the TV; the Component Video output
also sends all format source inputs to the TV.
Therefore, HDMI and Component Video are
the most convenient type of connection. It is
always possible to use Component or HDMI
as a single output connection, because the
RSX-1058 includes upconversion and scaling
for all video inputs. See the VIDEO INPUT/
OUPUT FORMATS list, on this page.
NOTE: When you have changed the output
resolution in the VIDEO/HDMI menu during
operation, restart by switching power OFF and
ON again, to stabilize the picture image in the
new resolution setup.

Publicité

Chapitres

Table des Matières
loading

Table des Matières