Zone Out Video Outputs; Digital Audio Input & Outputs; Digital Inputs; Digital Outputs - Rotel RSX-1058 Manuel D'utilisation

NOTE: HDTV Component Video output is
subject to HDCP copy protection. It may not
display 720p or 1080i resolution when the
source signal incorporates copy protection.
However, when Video Out is set to 480p/576p
in the VIDEO/HDMI menu, all sources will be
available. Component Video output is not avail-
able for 480i/576i images.
NOTE: Do not connect HDMI and Compo-
nent Video outputs to a monitor simultane-
ously, as the two video image signals may
affect each other.
HDMI connections:
• The RSX-1058 uses the HDMI Ver. 1.1
standard. TV monitors with HDMI inputs
should be compatible with this version.
• The video signal sent to the TV through the
HDMI connection will not be displayed
properly unless all HDMI components in
the system, including the TV monitor, are
compatible with the HDCP copy protec-
tion standard.
• Only audio signals passed-through directly
from the source component are sent to the
TV set through the HDMI connection. To
send decoded audio from the RSX-1058
to the TV, you must select 'TV mode' in
the VIDEO/HDMI menu.
• TV monitors with DVI-D connections can
usually be connected to the HDMI out-
put of the RSX-1058 with the use of an
appropriate 24-pin DVI-HMDI adaptor.
However, there are occasionally some in-
compatibilities with older DVI-D equipped
monitors.
• Use the scaler setting of the RSX-1058
'VIDEO OUT FORMAT' in the VIDEO/
HDMI menu to match the natiive resolu-
tion of the TV monitor.
• In general, HDMI is the optimum connec-
tion for digital high-definition monitors
such as LCD, plasma, or DLP monitors.
NOTE: Do not connect HDMI and Compo-
nent Video outputs to a monitor simultane-
ously, as the two video image signals may
affect each other.

ZONE OUT Video Outputs

The ZONE OUT Video outputs of the RSX-1058
send a Composite video signals to TV moni-
tors in Zone 2, 3 & 4.
19
NOTE: Only Composite video input signals are
available at the Zone 2, 3 & 4 video outputs.
Digital Audio
Input & Outputs
The RSX-1058 provides digital connections
which may be used in place of, or in addition
to, the analog audio input and output con-
nections described in the previous sections.
These connections include seven digital inputs
and also an HDMI Audio digital input. and
two digital outputs (for recording),
These digital connections can be used with
any source component that supplies a digi-
tal signal, such as a DVD player, CD player,
or satellite TV tuner.
NOTE: With a digital connection, the RSX-1058
will be used to decode the signal, rather than
the source component's internal decoders. In
general, you must use digital connections for a
DVD player or other component that supplies
a Dolby Digital or DTS signal; otherwise the
RSX-1058 will not decode these formats.

Digital Inputs

The RSX-1058 accepts digital inputs from
source components such as CD players, sat-
ellite TV tuners, and DVD players. The built-
in digital processor senses and adjusts to the
correct sampling rates.
There are seven digital inputs on the rear
panel, three coaxial and four optical, as well
as HDMI Audio input. These digital inputs
can be assigned to any of the input sources
using the INPUT SETUP screen during the
setup process. For example, you can assign
the COAXIAL 1 digital input connector to the
VIDEO 1 source and the OPTICAL 2 digital
input to the VIDEO 3 source. By default, the
source input buttons are factory configured
to select the following inputs:
CD: Digital Coaxial 2
Tuner: Analog (built-in)
Tape: Digital Coaxial 3
Video 1: HDMI Audio (HDMI 1)
Video 2: HDMI Audio (HDMI 2)
Video 3: Digital Optical 1
Video 4: Digital Optical 2
Video 5: Digital Coaxial 1
NOTE: When using digital connections, you
should also make the analog audio input con-
nections described previously. The analog con-
nection is necessary to record to an analog
recorder in some circumstances or for ZONE
2, 3 & 4 operation.

Digital Outputs

The RSX-1058 has two digital outputs (one
coaxial and one optical) to send the digital
signal from any of the digital inputs to a dig-
ital recorder or outboard digital processor.
When a digital input source signal is selected
for listening, that signal is automatically sent
to both digital outputs for recording.
NOTE: Only digital signals from source com-
ponents are available at these outputs. Analog
signals cannot be converted and are not avail-
able at the digital outputs.

Other Connections

AC Input

Your RSX-1058 is configured at the factory
for the proper AC line voltage in the country
where you purchased it (USA: 120 volts/60Hz
AC or CE: 230 volts /50 Hz AC ). The AC
line configuration is noted on a decal on the
back of your unit.
Plug the supplied cord into the AC INPUT re-
ceptacle on the back of the unit.
NOTE: Memorized settings and video labels
are preserved indefinitely, even if the RSX-1058
is disconnected from AC power.

Master Power Switch

The large rocker switch on the rear panel is
a master power switch. When it is in the OFF
position, power to the unit is completely off.
When it is in the ON position, the front-panel
STANDBY and remote control ON/OFF but-
tons can be used to activate the unit or put it
into standby mode.
NOTE: After all connections are completed,
the rear panel master power switch should
be put in the ON position and usually left in
that position.
English