Rds/Rbds Buttons; Basic Operations; Power And Standby On/Off; Volume Adjustments - Rotel RSX-1058 Manuel D'utilisation

RSX-1058 Surround Sound Receiver

RDS/RBDS Buttons

Four remote control buttons (DISP, PTY, TP, TA)
are used to activate various RDS/RBDS tuning
features. See the RDB/RBDS Tuning section of
the manual for detailed information.

Basic Operations

This section covers the basic operating con-
trols of the RSX-1058 and the remote.

Power and Standby On/Off

The rear panel POWER switch on the RSX-1058
is a master power switch. The button must
be in the ON position for the unit to oper-
ate. When it is in the OFF position, the unit
is fully off and cannot be activated from the
front panel or remote control.
In normal operation, the rear panel POWER
switch is always left in the ON position. The
RSX-1058 is activated and deactivated using
the front-panel STANDBY button, the remote
control POWER button, or the remote ON/
OFF buttons. When activated, the RSX-1058
is fully functional and the front-panel display
illuminated. When deactivated, the unit goes
into a standby mode, with minimal power ap-
plied to the microprocessor.
NOTE: When the unit has AC power ap-
plied and the rear panel POWER switch is on,
the front-panel STANDBY LED lights, regard-
less of whether the unit is in standby mode or
activated.
The front-panel STANDBY button and the re-
mote control POWER button function as tog-
gle switches. Press either button to activate
the unit. Press either button again to put the
unit in standby mode.
The ON/OFF buttons on the remote serve
the same function, but provide discrete ON
(active) or OFF (standby) commands.
NOTE: When using the Zone room capabil-
ity of the RSX-1058, the standby activation is
completely independent for the main room and
the zones. ON/OFF commands sent from the
remote in the main room will not affect Zones
2–4. Pressing the ON/OFF buttons on a remote
located in Zone 2, 3 or 4 will only affect that
zone and not the main room. When the unit is
activated in one of the zones, that zone's icon
is lit in the front-panel FL display.
There are four available power mode op-
tions, which may be useful in configuring the
RSX-1058 for special system configurations.
See the Other Options menu in the Setup sec-
tion of this manual for additional details on
changing the default standby behavior.
'Resume' retains the last power configura-
tion when the main power is switched OFF
and then switched ON again. For example,
if the RSX-1058 is in operation and the main
power is switched OFF, when the main power
is switched ON, the unit will be in operation
mode again.
All OFF command: A long press of the
OFF button (more than 3 seconds), from any
room, sets the RSX-1058 to standby.

Volume Adjustments

The listening volume of the RSX-1058 can be ad-
justed from the front panel or the remote.
Front Panel: Rotate the front-panel VOL-
UME knob clockwise to increase the volume,
counterclockwise to decrease.
Remote: Press the VOL UP button to in-
crease the volume; press the VOL DOWN
button to decrease.
When you adjust the volume, the setting
is shown on the SDTV monitor and/or the
front-panel display. The current volume set-
ting is also shown on the SYSTEM STATUS
OSD screen.
NOTE: The VOLUME controls can be used to
change the volume in Zone 2, 3 or 4. Press
the front-panel or remote control ZONE button
and adjust the volume. After 10 seconds, the
VOLUME control reverts to normal operation.

Muting the Sound

The volume of the RSX-1058 can be turned off
or muted. Push the MUTE button on the front
panel or the remote once to turn the sound
off. A MUTE indication appears in the OSD
and the front-panel displays. Press the MUTE
button again or adjust the volume settings to
restore output levels.
26

Selecting Inputs

Input Buttons

You can select any of nine source inputs for
listening and/or watching: CD, TUNER, TAPE,
VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, VID-
EO 5, or MULTI INPUT (EXT on remote).
The front-panel display and the ON-SCREEN
DISPLAY show the name of the current listen-
ing source selection. The labels for VIDEO
sources can be customized to match your
components.
NOTE: When the TUNER input source button
is pressed, the frequency of the currently tuned
station is displayed. Pressing the button again
toggles the display to show the word TUNER
instead of the frequency display.
All of the source inputs can be customized us-
ing the ON-SCREEN DISPLAY configuration
menus to accept either analog signals or digi-
tal signals from one of the seven assignable
digital inputs, or HDMI Audio. When a digi-
tal input is assigned, the RSX-1058 checks for
the presence of a digital signal at that input.
If a digital signal is present when the source
is selected, it is automatically activated and
the proper surround mode enabled. If no
digital signal is present, the analog inputs
for that source are selected. This auto-sens-
ing is the preferred configuration for digital
source inputs such as DVD players. When
an ANALOG input is assigned, the unit will
not access a digital signal, even though one
may be available at the digital input.
By default, the source input buttons are factory
configured to select the following inputs:
CD: Digital Coaxial 2
Tuner: Analog (built-in)
Tape: Digital Coaxial 3
Video 1: HDMI Audio (HDMI 1)
Video 2: HDMI Audio (HDMI 2)
Video 3: Digital Optical 1
Video 4: Digital Optical 2
Video 5: Digital Coaxial 1