SEL Button
REC Button
Press the front-panel SEL button or the remote
control REC button to select the desired zone
for additional changes such as changing the
input, adjusting the volume, or turning a re-
mote zone on or off. Repeatedly press the
button until the desired zone appears in the
front panel: RECORD > ZONE 2 > ZONE
3 > ZONE 4. Once the desired zone ap-
pears, you have 10 seconds to make the
desired change. Change the input selection
by pressing an INPUT button. When ZONES
2–4 appear, you can also adjust the volume,
or turn the zone on or off by pressing the
ZONE button.
A long press of the SEL or REC button is used
to cancel the PARTY mode and return all zones
to their last previously selected inputs.
ZONE Button
Either of these buttons serve as a standby
button for the currently-selected remote zone,
toggling the zone on or off. Select the desired
zone using the front-panel SEL or remote con-
trol REC button as described above.
UP/DOWN Buttons
These two buttons on the remote are used to
move the cursor up or down to select lines in
the OSD menus. These buttons are also used
in conjunction with the TONE button to make
CONTOUR/TONE adjustments.
+/– Buttons
These two buttons on the remote are used
to change settings on a selected line in the
OSD menus. Also used for selecting options
in some surround modes.
Speaker Selection Buttons
These three buttons on the remote are used
to select a speaker or group of speakers for
temporary level adjustments. In addition, the
C button is used in conjunction with the UP/
DOWN buttons for temporary adjustment of
group delay/lip synch.
EQ Button
This button on the remote is used to turn on
and off the Cinema EQ feature, a high-cut
filter useful for older movie soundtracks.
25
TONE Button
This button on the remote is used for tempo-
rary Contour adjustments. It toggles between
high frequency (HF) and low frequency (LF)
modes. Once a mode is selected, the UP/
DOWN buttons are used to make the adjust-
ments to the speaker or speakers selected in
the Contour Setup menu.
NOTE: Permanent contour adjustments can be
made using the Contour Setup menu.
Surround Mode Buttons
Five buttons on the remote (2CH, PLC, PLM,
5CH, 7CH) and four buttons on the front
panel (2CH, DOLBY PLIIx Mode, DTS/Neo 6,
DSP) allow direct selection of certain surround
modes. The function of these buttons varies
depending on the type of recording being
played. See the Manually Selecting Surround
Modes section for detailed information.
SUR+ Button
This button on the remote is used in conjunc-
tion with the +/– buttons for manual selec-
tion of surround modes and features. See the
Manually Selecting Surround Modes section
for information.
DYN Button
Used the DYN button on the remote to select
the dynamic range control setting in Dolby
Digital surround mode.
MENU/OSD Button
Push this button on the remote to turn on the
OSD menu system. If the menu system is al-
ready visible, push this button to cancel the
display. Press and hold the button to turn off
the front-panel display.
ENTER Button
The ENTER button is used to confirm and
memorize various settings in the setup and
operation of the RSX-1058. Its use is described
in detail in the relevant sections.
BAND Buttons
Press either of the BAND buttons to toggle
between AM and FM reception.
TUNING Buttons
The TUNING buttons (labeled CH UP/DOWN
on the remote control) provide three different
tuning functions, depending on the mode of
operation: frequency tuning, preset tuning, or
selection of an RDS/RBDS program type.
MEM Button
The front-panel MEMORY button or remote
control MEM button (also labeled "X") is
used with the NUMERIC buttons to store
station presets.
NUMERIC Buttons
The NUMERIC buttons on the front panel or
the remote are used to enter the number of
a memorized station preset or for direct en-
try of a station frequency.
DIRECT Button
FRQ DIRECT Button
The front-panel DIRECT and remote control
FRQ DIRECT buttons are used in conjunction
with the NUMERIC buttons for direct entry of
a station frequency in AM/FM tuning.
MONO Button
FM MONO Button
The front-panel MONO and remote control
FM MONO buttons change the FM mode from
stereo reception to mono reception.
TUNE Button
PRESET Button
P-TUN Button
The TUNE, PRESET, and P-TUN buttons on
the remote are used to select FREQUENCY
tuning or PRESET tuning modes. The TUNE
and PRESET buttons select the modes direct-
ly. The P-TUN button toggles between the
two modes.
SCAN Button
Preset scan tuning automatically scans through
the memorized station presets, playing each
for 5 seconds. Press the SCAN button on the
remote to begin preset scanning. Press the
button again to stop the scanning and listen
to the desired preset.
English