Cable, Satellite, Hdtv Tuner; Audio Recorder; Vcr Or Digital Video Recorder; Dvd-A Or Sacd Player - Rotel RSX-1058 Manuel D'utilisation

the same video input source used above. If an
HDMI connection is used, assign HDMI Audio
for the digital audio, or one of the OPTICAL
IN or COAXIAL IN digital inputs.
Analog audio connections:
If you want to record the audio signal from
the DVD player or distribute the audio signal
to Zones 2–4, connect the left and right ana-
log outputs from the DVD player to the left
and right AUDIO IN jacks corresponding to
the VIDEO IN input selected above.

Cable, Satellite, HDTV Tuner

See Figure 8
Standard Definition TVs:
In a system with a standard definition TV,
cable or satellite tuner connections can be
made to the VIDEO 1, 2, 3, 4, or 5 inputs.
You may wish to use assigned Video Inputs
with interlace picture. The video picture is
then available by the assigned Video Input.
The analog audio is the same as the input
labelled terminals.
The video setting in each video source is by
assignment, so the INPUT labels of VIDEO 1-5
do not relate to video terminal numbers.
It is possible to assign any type of video ter-
minals, from the available three Composite
Video, three S-Video, three Component Vid-
eo and four HDMI.
If the monitor used is SDTV, an interlace source
(480i/576i) should be used.
NOTE: If you plan to distribute video from the
tuner to a TV monitor in Zone 2, 3 or 4, you
must make a composite video connection.
High Definition TVs:
It is possible to connect any video input for
use with an HDTV monitor, as the RSX-1058
has a built-in video converter and scaler in-
side. However, the higher the resolution of
the input signal, the higher the quality of
the picture.
With a high-definition cable or satellite tuner
and an HDTV monitor, you should use Com-
ponent Video and/or HDMI video connec-
tions from the tuner. If the tuner has a DVI-D
output, this can usually be connected to the
HDMI input on the RSX-1058 using a DVI-
HDMI adapter.
21
Connect a set of Component Video cables
or an HDMI cable from the tuner to the ap-
propriate input on the RSX-1058.
Digital Audio connections:
Connect the digital output of the tuner to
any one of the OPTICAL IN, COAXIAL IN
or HDMI IN digital inputs on the RSX-1058.
Use the INPUT SETUP screen to assign that
digital input to the same video input source
used above. For example, if you use the Vid-
eo 4 inputs above, assign the digital input to
the HDMI IN 1 input.
Analog audio connections:
If you want to record the audio signal from
the tuner to a VCR or distribute the audio sig-
nal to Zones 2–4, connect the left and right
analog outputs from the DVD player to the
left and right AUDIO IN jacks corresponding
to the VIDEO IN input selected above.

Audio Recorder

See Figure 11
Connect the left and right analog outputs from
an audio tape deck to the AUDIO IN jacks
labeled TAPE IN (left and right).
Connect the left/right AUDIO OUT/TAPE OUT
jacks to the inputs on the audio tape deck.
Optional: For a digital recording device,
connect the digital output of the recorder to
one of the OPTICAL IN or COAXIAL IN dig-
ital inputs on the RSX-1058. Use the INPUT
SETUP screen to assign that digital input to the
TAPE source. If the recording device accepts
a digital recording input, connect either the
OPTICAL OUT or COAXIAL OUT connection
to the digital input of the recorder.
No video connections are required for an
audio recording device.

VCR or Digital Video Recorder

See Figure 9
VCR connections can be made to the VID-
EO 1, VIDEO 2, or VIDEO 3 inputs and out-
puts. If you choose VIDEO 1, make sure that
you use either Composite or S-Video inputs
and outputs for all analog audio and video
connections.
Connect video cables (Composite Video,
S-Video, and/or Component Video) from the
output of the VCR to the appropriate video
input which is assigned.
Connect video cables (Composite Video
and/or S-Video) from the VIDEO OUT jacks
to the VCR inputs.
Connect the left and right analog outputs
from the VCR to one pair of the AUDIO IN
jacks labeled VIDEO 1–3.
Connect the left and right AUDIO OUT
jacks for VIDEO 1–2 to the analog inputs
on the VCR.
Optional: For a digital recording device,
you can use digital audio connections. Con-
nect the digital output of the recorder to one
of the OPTICAL IN or COAXIAL IN digital
inputs on the RSX-1058. Use the INPUT SET-
UP screen to assign that digital input to the
VIDEO source (VIDEO 1, 2, or 3) used for
the previous connections. If the recording
device accepts a digital recording input,
connect one of the OPTICAL OUT or CO-
AXIAL OUT connections to the digital input
of the recorder.

DVD-A or SACD Player

See Figure 7
To hook up a DVD-A, a SACD player, or any
external surround decoder, use audio RCA
cables to connect the outputs of the player to
the RCA jacks labeled MULTI INPUT, making
sure that you observe proper channel consis-
tency, i.e. connect the right front channel to
the R FRONT input, etc. Depending on your
system configuration, make six connections
(FRONT L & R, SURROUND L & R, CENTER,
and SUBWOOFER), seven connections (add-
ing a CENTER BACK connection), or eight
connections (adding two CENTER BACK
connections).
The MULTI inputs are analog bypass inputs,
passing signals directly through to the Vol-
ume Control and preamp outputs, bypassing
all of the digital processing. The RSX-1058
provides an optional bass redirect feature
that duplicates the seven main channels and
passes them through an analog 100 Hz low
pass filter, creating a summed mono sub-
woofer output derived from the main chan-
nels. See the INPUT SETUP menu in the Set-
up section of this manual for details on bass
redirect feature.
English