More Information; Troubleshooting - Rotel RSP-1069 Manuel D'utilisation

RSP-1069 Surround Sound Processor
If the entered password is correct, the
current settings will be saved as the new
USER DEFAULT settings.
3. To return to the MAIN menu without sav-
ing changes, change all entries on the
screen to NO and press ENTER.
: If there is insuffi cient memory to store a
NOTE
USER DEFAULT confi guration fi le, the SET USER
DEFAULT option will not be available.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT confi guration fi le, you can activate
those settings at any time by placing the
highlight on the USER DEFAULT line using the
UP/DOWN buttons. Use the +/– buttons to
change the setting to YES. Press the ENTER
button to proceed with activating the USER
DEFAULT settings. To return to the MAIN
menu without activating the USER DEFAULT
settings, change the entry to NO and press
the ENTER button.
To return to the MAIN menu without activating
the USER DEFAULT settings, change the entry
to NO and press the ENTER button.
To change the password: The password
programmed at the factory is 0000. If you
wish to change the password:
1. Place the highlight on the SET NEW PASS-
WORD line using the UP/DOWN buttons.
Use the +/– buttons to change the setting
to YES. Press the ENTER button to proceed
to the PASSWORD screen.
2. Enter the four digits of the old password by
pressing the +/– buttons to select the fi rst
letter of the new password, then pressing
ENTER to move to the second character.
Repeat until the old password is entered.
Successful entry of the old password will
jump to the ENTER NEW PASSWORD
line.
3. Enter the four digits of the new password
by pressing the +/– buttons to select the
fi rst letter of the new password, then press-
ing ENTER to move to the second char-
acter. Repeat until the new password is
entered.
4. You will be asked to re-enter the password
again on the CONFIRM PASSWORD line,
following the same procedure. Once the
password is successfully confi rmed, it will
be saved and you will return to the DE-
FAULT SETUP MENU automatically.
5 To exit the PASSWORD screen without
changing the password, highlight the
DEFAULT SETUP MENU line and press
ENTER to return to the previous screen.
: The factory password is 0000. A
NOTE
default password that will always be recog-
nized is 8888.
46

MORE INFORMATION

Troubleshooting

The unit does not turn on.
• Make sure the power cord is plugged
into the rear panel and a live AC wall
outlet.
• Make sure the rear panel POWER switch
is in the ON position
No sound from any input.
• Make sure that MUTING is off and VOL-
UME is turned up.
• Make sure that preamp outputs are con-
nected to a power amplifi er and that the
amplifi er is turned on.
• Make sure source inputs are connected
and confi gured correctly.
• Check that the setting for HDMI AUDIO
in the VIDEO/HDMI on-screen menu is
AMP MODE.
No sound from digital sources.
• Make sure that digital input connector is
assigned to the proper source input and
that the source input is confi gured to use
the digital input rather than an analog
input.
• Check the confi guration of the DVD player
to ensure that the bitstream and/or DTS
digital output is activated.
No sound from some speakers.
• Check all power amp and speaker con-
nections.
• Check Speaker Confi guration settings in
the Setup menus.
No video output on TV monitor.
• Make sure that the TV monitor is connected
properly and check the input assignments.
S-Video and Composite Video TV moni-
tors can only be used with interlaced SD
sources. HDMI and Component TV moni-
tors can be used with Standard Defi nition
(SD) and High Defi nition (HD) sources. An
HDMI 1080p source can only be sent to
a 1080p-compliant TV monitor.