Publicité
ATTENTION
Product damage!
If the product is operated without oil or with too little oil
or with used oil, this can lead to product damage.
–
Fill with oil before starting the machine. The product
is delivered without oil.
–
Do not use used oil!
–
Check the oil level every time you change the bat-
tery.
ATTENTION
Environmental damage!
Spilled oil can pollute the environment permanently.
The liquid is highly toxic and can quickly lead to water
pollution.
–
Fill/empty oil only on level, paved surfaces.
–
Use a filling nozzle or funnel.
–
Collect drained oil in a suitable container.
–
Wipe up spilled oil carefully immediately and dis-
pose of the cloth according to local regulations.
–
Dispose of oil as per local regulations.
The saw chain will be lubricated automatically while the
product is running. To lubricate the saw chain sufficiently,
there must always be enough saw chain oil in the oil tank.
Check the amount of oil remaining in the oil tank at regu-
lar intervals.
Note:
• The cover is equipped with an anti-loss device.
• Only add environmentally friendly, good quality chain
lubricating oil (per RAL-UZ 48) to the chain saw.
• Ensure that the cover of the oil tank is in place and
closed before switching on the product.
1. Open the oil tank (14). To do this, unscrew the oil tank
cap (14) anti-clockwise.
2. To prevent oil from leaking, use a funnel*.
3. Carefully add the chain lubricating oil until it reaches
the top mark on the oil level indicator (13). Oil tank ca-
pacity: max. 260 ml.
4. Screw down the cover of the oil tank (14) clockwise to
close the oil tank (14).
5. Wipe up any spilled oil carefully immediately and dis-
pose of the cloth* according to local regulations.
6. To check the product lubrication, hold the chainsaw
with the saw chain over a sheet of paper and give it
full throttle for a few seconds. You can see on the pa-
per whether the chain lubrication is working.
* = not included in the scope of delivery!
8.4
Inserting/removing the batteries
(20) in the battery mounts (4)
(Fig. 4)
CAUTION
Danger of injury!
Do not insert the battery until the battery-powered tool
is ready for use.
Inserting the battery
1. Slide the batteries (20) into the battery mounts (4).
The batteries (20) click into place audibly.
Removing the battery
1. Press the unlock button (21) of the battery (4) and re-
move the batteries (20) from the battery mounts (4).
8.4.1
The charge status indicator (11) indicates the charge sta-
tus of the battery (20).
The charge status of the battery is indicated by the corre-
sponding LED light lighting up.
1. Press the button on the charge level indicator (11) to
check the charge level.
3 LEDs illuminate
2 LEDs illuminate
1 LED illuminates
8.5
Safety devices (Fig. 1)
• Rear handle (1) with hand guard
– Protects the hands from branches and twigs and if
the chain jumps off.
• On/off switch (2) with chain instant stop
– Switches the product off immediately if the on/off
switch is released.
• Chain brake/front hand guard (6)
– Safety devices that stop the saw chain immediate-
ly in the event of kick-back.
– The lever can also be manually actuated.
– Protects the left operator's left hand if it slips off
the front handle.
• Saw chain (7) with low kick-back
– Helps you to intercept kick-backs with specially
developed safety devices.
• Switch lock (12)
– To switch on the product, the switch lock must be
unlocked.
• Claw stop (15)
– Reinforces stability when vertical cuts are per-
formed and makes sawing easier.
9
Operation
The cordless chain saw is equipped with a quick-tension-
ing system for the chain. The saw chain runs around the
edge of the guide bar (guide rail). An automatic oil system
ensures continuous chain lubrication. To protect the us-
www.scheppach.com
Charge level indicator (11) (Fig. 4)
Battery fully charged
Battery partially charged
Battery must be charged
GB | 31
Publicité
