Publicité
M o d e l l s p o r t
Congratulations on your purchase of the new CYCLONE XT.
The CYCLONE XT is a thermal motorglider with a dynamic flight envelope. It can be flown within in
a broad speed range. There are various ways of constructing the model, depending on your prefe-
rences. Therefore the solutions stated in this manual should only be considered as recommendations.
For the most parts, the PNP (plug and play) version is already prefabricated.
The ARF version (almost ready to fly) requires modeling experience and basic technical knowledge in
construction. Thus there are different ways to achieve a model with good flight skills. This is why most
alternatives are in fact explained in the manual but not necessary shown in the pictures.
Please read this manual carefully before you start assembling the model.
F L I G H T I N S T R U C T I O N S
• Before the first flight, observe the instructions in the „Safety Instructions" section.
• When flying the model, you should choose a day with as little wind as possible
• A large, flat area without obstacles (trees, fences power lines etc.) is suitable for the first flights.
• Please carry out a functional test of the drive train / power set and remote control.
• After assembling the model on the airfield, check once again that all model components such as
wing, tail units, wing mounts, engine, linkages, etc. are firmly and properly fastened.
• For a hand start a helper should be present, who can throw the model with enough thrust into the
air.
• The start usually takes place against the wind.
• Do not stall the model near the ground
• Do not initiate tight turns in the immediate vicinity of the ground.
• Check the reactions of the model to the rudder deflections. If necessary, adjust after landing to
increase or decrease the deflections accordingly.
• The minimum flight speed must be at an adequate safety altitude.
• Initiate the landing with sufficient speed
S A F E T Y I N S T R U C T I O N S F O R R E C H A R G E A B L E B A T T E R I E S
• Do not immerse the battery in water or other liquids.
• Do not heat, throw into fire or microwave.
• Do not short-circuit or charge with reversed polarity
• Do not expose, deform or throw the battery
• Do not solder directly on the battery
• Do not change or open the battery
• Only charge the battery with suitable chargers, never connect it directly to a power supply unit.
• Never charge or discharge the battery or charger on a flammable surface.
• Never leave the battery unattended during charging or discharging processes.
• Never charge or discharge the battery in direct sunlight or near heaters or fire.
• Do not use the battery in places subject to high static discharge.
All this can cause the battery to be damaged, explode or even catch fire!
• Keep the battery away from children
• Keep leaked electrolyte away from fire, as it is highly flammable and may ignite.
• The electrolyte liquid should not get into the eyes, if it does, rinse immediately with plenty of clear
water and then see a doctor.
• The electrolyte liquid can also escape from clothes and other objects with a lot of water or washed
off.
• Observe the safety instructions of the battery manufacturer and the charger manufacturer.
I N S T R U C T I O N S A N D U S E R M A N U A L
P R E F A C E
T E C H N I C A L D A T A
Span
6200 mm
Length
2250 mm
Flying weight PNP
11400 g
Flying weight ARF
-
Wing Area
175,6 dm²
HQ/W-2,5/12 + HQ/W-
Airfoil
2,5/11 + HQ/W-3/10,5
110 to 120 mm behind the
C.G.
leading edge
B O X C O N T E N T / N E E D E D A C C E S S O R I E S
Item number
Accessories needed
Motor
5836
Ro-Power Torque LS 6330-15
ESC
8717
Ro-Control PRO 14-130A
Battery
7348
2x RO-POWER ULTRA HP 5200MAH 14,8 V 4S LiPo
Servo ELE
Not yet known 1x Robbe FS-0150 MG BB HV
Servo RUD
Not yet known 1x Robbe FS-0150 MG BB HV
Servo AILE
Not yet known 2x Robbe FS-0150 MG BB HV
Servo FLAP
Not yet known 2x Robbe FS-0150 MG BB HV
Servo LANDING FLAP
-
no
ROBBE Servo cable Graupner/JR/Uni 10m
Servo cable
46243
twisted, 0,33mm²
Landing gear
-
no
MULTIlock
725142
yes MULTIlock Uni Set
MPX plugs /
40004, 40011 /
yes MPX plugs / 4 pair mounting frame
Mounting frame
50047
Adhesives
45900
UHU Por Tube 40g
Epoxy resin
50601
5min ro-POXY adhesive 200g
Locking screw
L2088
yes
Velcro strap
59001010
Robbe Velcro strap 3M 30x1000mm
Spinner
20838
Alu Turbo Spinner 50mm
Propeller
C2F2008
Propeller 20 x 8" Carbon
TX
-
min. 7 channels
RX
-
min. 7 channels
Declaration:
LF: Box content
Elevator
Rudder
Ailerons
Flaps
Landing flaps
Motor
LF : ARF
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-: not included
X: included
yes
yes
yes
yes
no
yes
LF: PNP
X
-
-
X
X
X
X
-
X
-
X
X
-
-
-
-
X
X
-
-
9
Publicité
