Publicité
M o d e l l s p o r t
capacity. Avoid strong bending or tensile stress on the connecting cables. After termination of flight or
driving operation, disconnect the battery to prevent deep discharge of the battery. This would cause
permanent damage. For the BEC version of the controller, check that the BEC power of the device is
sufficient for the servos used. Speed controllers should be installed as far away as possible from other
remote control components. We recommend carrying out a range test before operation. We recom-
mend regular checking of the controller for function and externally visible damage. Do not continue
operating the controller if you notice any damage. The connection cables must not be extended.
This can lead to unwanted malfunctions. Despite existing safety and protective devices of the device,
damage may occur which is not covered by warranty. The warranty also expires if changes are made
to the device.
Important information:
The receiver system is powered by the built-in BEC system of the controller.
For commissioning, always move the throttle stick to the „Motor off" position and switch on the trans-
mitter. Only then connect the battery. To switch off always disconnect the connection battery motor
controller, first then turn off the transmitter. During the functional test, move the servos of the rudders to
neutral position with the remote control (stick and trimming lever on the transmitter to the middle positi-
on). Please make sure to leave the throttle stick in the lowest position so that the engine does not start.
For all work on to the parts of the remote control, motor or controller, follow the instructions supplied
with the units. Also read the instructions of the battery and the charger carefully before commissioning.
Check the engine mounting bolts in the fuselage regularly for tightness.
Our articles are equipped with the legally required 24 months warranty. Should you wish to assert
a justified warranty claim, always contact your dealer, who is responsible for the warranty and the
processing. During this time, any functional defects that may occur, as well as manufacturing or other
problems, will be rectified.
Material defects corrected by us free of charge. Further claims, e.g. for consequential damages, are
excluded.
The transport to us must be free, the return transport to you is also free. Freight collect shipments can-
not be accepted. We cannot accept liability for transport damage and loss of your consignment. We
recommend appropriate insurance.
To process your warranty claims, the following requirements must be met:
• Attach the proof of purchase (receipt) to your shipment.
• The units have been operated in accordance with the operating instructions.
• Only recommended power sources and original robbe accessories have been used.
• There is no moisture damage, external interference, reverse polarity, overloading or mechanical
damage.
• Attach relevant information for finding the fault or defect.
I N S T R U C T I O N S A N D U S E R M A N U A L
W A R R A N T Y
Robbe Modellsport cannot monitor compliance with the assembly and operating instructions or the
conditions and methods for installation, operation, use and maintenance of the model components.
Therefore, we accept no liability for losses, damage or costs arising from or in any way connected with
incorrect use and operation.To the extent permitted by law, the obligation to pay damages, irrespec-
tive of the legal grounds, shall be limited directly to the invoice value of the claims arising from the
event causing the damage.
Ground-based models are usually covered by personal liability insurance. Additional insurance or
extension is required for aircraft models. Check your insurance policy (private liability) and take out
suitable insurance if necessary.
C O N F O R M I T Y
Robbe Modellsport hereby declares that this device complies with the es-
sential requirements and other relevant regulations of the corresponding CE
directives. The original declaration of conformity can be found on the Internet
at www.robbe.com, in the detailed product view of the respective device
description or on request. This product can be operated in all EU countries.
This symbol means that small electrical and electronic devices must be dis-
posed of at the end of their useful life, separated from the household refuse.
Dispose of the device at your local municipal collection point or recycling
centre. This applies to all countries of the European Union and other European
countries with a separate collection system.
Made in China
D I S C L A I M E R
I N S U R A N C E
D I S P O S A L
M o d e l l s p o r t
+14
5
Publicité
