LiftMaster LM3800W-2 Mode D'emploi page 12

To repeat the read out, disconnect RJO from power and start again.
Light transmitter (with 78EV): Enables learning a transmitter to the MyQ Remote via Multifunction wall control.
To programm transmitter to MyQ Remote LED Light:
1. Press and hold the LIGHT & LOCK button together.
2. While holding above both buttons, press & hold one of the button on transmitter until RJO WorkLight flashes once.
3. After the opener WorkLight flashes once, release all buttons.
Vacation Mode (requires 78EV wall control). Portable remote controls do not function if this feature is activated. See instructions of 78EV.
Keyless entry (requires 747EV wireless keypad): Enter a 4 digit code of your choice to operate the door.
Temporary access (requires 747EV wireless keypad): A temporary code can be programmed to allow limited access to the garage (by time or
number of openings).
One button close feature (requires 747EV wireless keypad): Without having the access code the door can be closed from any position (not
opened).
24 Connect With Your Smartphone
The Wi-Fi Garage Door Opener is compatible with up to 16 MyQ enabled accessories. Up to 10 devices can be paired to the Wi-Fi garage door
®
opener's internal gateway. These devices can be controlled with the MyQ app. These devices include any combination of MyQ garage door openers,
Wi-Fi garage door openers, MyQ light, MyQ gate operators. A LiftMaster Internet Gateway (828EV) can be added if you need to control more than 10
devices using the MyQ app. Up to 6 devices can be paired to garage door opener itself (controlled by garage door opener). These devices include
any combination of MyQ light or a garage door and gate monitor.
You will need:
• Wi-Fi enabled smartphone, tablet or laptop
• Broadband Internet Connection
• Wi-Fi signal in the garage (2.4 Ghz, 802.11b/g/n required)
• Password for your home network (router's main account, not guest network)
• MyQ serial number located on the garage door opener
• Infrared photocells (required accessory)
• MyQ Remote LED Light (in delivery scope)
SYNCHRONIZE THE DOOR CONTROL
To synchronize the door control 78EV to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3
presses).The garage door opener must run through a complete cycle before it will activate Wi-Fi programming.
CONNECT YOUR GARAGE DOOR OPENER TO YOUR HOME WI-FI NETWORK
1. Press and release the yellow LEARN button (L) on the garage door opener 3 times. The garage door opener will beep once. You have 20
minutes to complete the connection process.
2. On your mobile device, go to Settings > Wi-Fi and select the network with the "MyQ-" prefix.
3. Launch the web browser on your smartphone or tablet. Enter setup.myqdevice.com into the browser address bar. Follow the on screen prompts
to connect the garage door opener to your Wi-Fi network. The MyQ serial number will display on screen. Write the serial number in the space
below.
4. Download the MyQ app from the App Store
account.
To add a second Wi-Fi garage door opener, repeat steps 1-3. Add the second MyQ serial number to your account in the MyQ app.
NOTES: The MyQ Smartphone Control WILL NOT work if the garage door opener is operating on battery power. To erase the Wi-Fi settings, see
page 15.
An LED (A) on the garage door opener will indicate Wi-Fi status. See table below
LED
BLUE
BLUE AND GREEN
GREEN
or Google Play
®
DEFINITION
Off - Wi-Fi is not turned on.
Blinking - Garage door opener is in Wi-Fi learn mode.
Solid - Mobile device connected to the garage door opener.
Blinking - Attempting to connect to router.
Blinking - Attempting to connect to the Internet server.
Solid - Wi-Fi has been set up and garage door opener is connected to the Internet.
store. Sign up for your MyQ account and add the MyQ serial number to your
™
11 / en