LiftMaster LM3800W-2 Mode D'emploi page 11

To Exit uncompleted TTC programming mode, please press and release the learn button (L) one more time.
TTC Timing Change:
1. Press learn button (L) 4 times again.
2. Cycle through OFF /1/5/10 minutes increments using the UP (U) and DOWN (D) arrows. Yellow learn LED shall blink upon selection.
3. Press rectangular adjustment button (A) to save the setting and exit the TTC programming mode.
When activation has completed the MyQ Remote LED Light will flash ONE time as a confirmation.
TTC Deactivation:
1. Press yellow Learn button (L) 4 times.
2. Press adjustment button one time to save the setting.
3. When deactivation has been completed the MyQ Remote LED Light shall flash ONCE as a confirmation.
If the TTC is active, the timer is counting down, and the IR beams are interrupted, the TTC timer shall be restarted.
MyQ
MyQ allows you to control your garage door opener from your mobile device or computer from anywhere. MyQ technology uses a radio signal to
provide two way communication between the garage door opener and MyQ enabled accessories. The garage door opener has an internal gateway
that allows the garage door opener to communicate directly with a home Wi-Fi
INFRARED PHOTOCELLS
When properly connected and aligned, the infrared photocells will detect an obstruction in the path of the infrared beam. If an obstruction breaks the
infrared beam while the door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times. If the door is fully
open with infrared photocells installed, and are misaligned, the door will not close from a remote control. However, you can close the door if you hold
the button on the door control or keyless entry until the door is fully closed. The infrared photocells do not affect the opening cycle.
ENERGY CONSERVATION
For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. The sleep mode shuts the garage door opener
down until activated. The sleep mode is sequenced with the garage door opener light; as the light turns off the sensor LEDs will turn off and when-
ever the garage door opener lights turn on the sensor LEDs will light. The garage door opener will not go into the sleep mode until the garage door
opener has completed 5 cycles upon power up.
LIGHTS
The garage door opener light will turn on when the opener is initially plugged in; power is restored after interruption, or when the garage door opener
is activated. The light will turn off automatically after 4-1/2 minutes.
LIGHT FEATURE
The garage door opener is equipped with an added feature; the lights will turn on when someone enters through the open garage door and the
infrared beam is broken. Infrared photocells 771EV / 772E / 771EVK / G770E need to be installed to enable this feature.
BATTERY BACKUP (OPTIONAL)
The battery backup system allows access in and out of your garage, even when the power is out. When the garage door opener is operating on bat-
tery power, the garage door opener will run slower, the light will not function, the Battery Status LED will glow solid orange, and a beep will sound
approximately every 2 seconds.
USING YOUR GARAGE DOOR OPENER
The garage door opener can be activated through a wall-mounted door control, remote control, wireless keyless entry or MyQ accessory. When
operating the door opener by radio control or wall switch:
• closes the door when it is fully open
• opens the door when it is fully closed
• stops the door if it is opening or closing
• the door moves in the opposite direction to the last completed move,
if it is partially open If the door senses an obstruction or is interrupted while opening the door will stop. If the garage door opener senses an obstruc-
tion while closing, the door will reverse. If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times. However, you
can close the door if you hold the button on the door control or keyless entry until the door is fully closed. The infrared photocells do not affect the
opening cycle.
CYCLE COUNTER.ACTIVATION AND READING PROCEDURE:
1. Disconnect power from RJO to enter into this mode.
2. Press the Adjustment (A) and Learn buttons (L) and hold together upon restoring power.
3. Operator "UP" arrow button (U) LED will flash ONE time for each thousand FULL cycles completed as long as the Adjustment (A) and Learn
buttons (L) are pressed and held.
For example, if the RJO has made 8756 cycles, UP LED shall blink 8 times.
network and access your MyQ account.
®
10 / en